manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 2005 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2005

crankshaft pulley. 
Are the CKP sensor and 
teeth of crankshaft 
pulley normal?

No

Replace the malfunctioning part.

6

Inspect the spark plug 
condition. 
Is spark plug wet, 
covered with carbon or 
grayish white?

Yes

Spark plug is wet or covered 
with carbon:

  

Inspect the fuel injector for fuel 
leakage. 
Inspect spark plug and high-
tension lead. 

Spark plug is grayish white:

  

Inspect the fuel injector for 
clogging.

No

Install the spark plugs on 
original cylinders. Go to the 
next step.

7

Remove and shake the 
PCV valve. 
Does the PCV valve 
rattle?

Yes

Go to the next step.

No

Replace PCV valve.

8

Perform electronic 
throttle control system 
operation inspection. 
(See 

ELECTRONIC 

THROTTLE 
CONTROL SYSTEM 
INSPECTION

 .) 

Does electronic throttle 
control system function 
properly?

Yes

Go to the next step.

No

Repair or replace the 
malfunctioning part according to 
electronic throttle control 
system operation inspection 
results.

9

Visually inspect 
deformed exhaust 
system part. 
Is there any deformed 
exhaust system part?

Yes

Replace the suspected part.

No

Go to the next step.

10

Install the fuel pressure 
gauge between the fuel 
pipe and the fuel 
distributor. 
Short check connector 
terminal F/P to body 
GND using a jumper 
wiring. 
Turn the ignition switch 
to the ON position. 
Is fuel line pressure 

Yes

Go to the next step.

No

Zero or low:

  

Inspect the fuel pump relay and 
fuel pump circuit. Inspect the 
fuel line for clogging. 
If there is no malfunction, 
replace the fuel pump unit. 
(See 

FUEL PUMP UNIT 

REMOVAL/INSTALLATION 
[LF]

 .) 

High:

  

 

2007 Mazda MX-5 Miata Sport 

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:42:10 PM

Page 72 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов