Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 326 | Manualshive

Страница: 326 / 2244

background image

Fig. 23: Removing/Installing Seat Weight Sensor Control Module

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

SEAT WEIGHT SENSOR CALIBRATION

CAUTION:



If any of the following work is performed, perform the seat weight
sensor calibration using the WDS or equivalent.



Replacement with a new seat weight sensor



Replacement with a new seat weight sensor control module



Replacement with new passenger-side seat parts



Disassembly of the passenger-side seat



If any of the following work is performed, perform the seat weight
sensor inspection using the WDS or equivalent. (See SEAT WEIGHT
SENSOR INSPECTION .)



Removal of the passenger-side seat



Loosening and retightening of passenger's seat fixing bolts

2007 Mazda MX-5 Miata Sport

2007 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:12:55 PM

Page 26

© 2005 Mitchell Repair Information Company, LLC.

«
...
324
325
326
327
328
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: PAC Страницы: 15

Бренд: ABL Страницы: 176

Бренд: ABL Страницы: 94

Бренд: Ford Страницы: 52

Бренд: DEFA Страницы: 7

Бренд: Prorack Страницы: 15

Бренд: Axxess Страницы: 8

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Wireless Handsfree Car Kit

Бренд: Wagan Страницы: 20

Xplore Pro II SxS

Бренд: Marlon Страницы: 15

Бренд: Whispbar Страницы: 15

Бренд: Gator Страницы: 2

Бренд: Rugged Ridge Страницы: 3

Бренд: Power Acoustik Страницы: 4

Prime Design OCM-3032

Бренд: Safe Fleet Страницы: 4

Бренд: Ford Страницы: 256

Бренд: Magneti Marelli Страницы: 3

Бренд: FIRRAK Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды