Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2040 | Manualshive

Страница: 2040 / 2244

background image

DIAGNOSTIC PROCEDURE

EXHAUST SULPHUR SMELL DIAGNOSTIC PROCEDURE TABLE

POSSIBLE CAUSE

warnings before servicing fuel system:



Fuel vapor is hazardous. It can easily
ignite, causing serious injury and
damage. Always keep sparks and
flames away from fuel.



Fuel line spills and leakage are
dangerous. Fuel can ignite and cause
serious injuries or death and
damage. Fuel can also irritate skin
and eyes. To prevent this, always
complete "BEFORE SERVICE
PRECAUTION" and "AFTER SERVICE
PRECAUTION" described in this
article.

(See BEFORE SERVICE
PRECAUTION [LF] .)

(See AFTER SERVICE PRECAUTION
[LF] .)

CAUTION:



Disconnecting/connecting quick
release connector without cleaning it
may cause damage to fuel pipe and
quick release connector. Always
clean quick release connector joint
area before
disconnecting/connecting, and make
sure that it is free of foreign material.

STEP

INSPECTION

RESULTS

ACTION

1

Are any driveability or
exhaust smoke
concerns present?

Yes

Go to the appropriate flow table.

No

Go to the next step.

2

Inspect the following:



Electrical
connections



Vacuum lines



Fuel quality

Yes

Go to the next step.

No

Service if necessary. Repeat
Step 2.

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:11 PM

Page 107

© 2005 Mitchell Repair Information Company, LLC.

«
...
2038
2039
2040
2041
2042
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Hama Страницы: 2

Бренд: TATA Motors Страницы: 161

Бренд: TAUBENREUTHER Страницы: 11

Бренд: Yakima Страницы: 15

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: Farad Страницы: 8

Бренд: Veigel Страницы: 24

Бренд: Cellular Line Страницы: 25

Бренд: Saab Страницы: 12

Бренд: Vauxhall Страницы: 259

Vehicle Asset Communicator

Бренд: I.D. Systems Страницы: 41

Бренд: Gator Страницы: 8

Бренд: benbat Страницы: 14

Бренд: SPL Страницы: 5

Бренд: ULTIMATE SPEED Страницы: 40

Бренд: Brink Страницы: 26

Prime Design VBI-FT31B

Бренд: Safe Fleet Страницы: 12

Бренд: r.LiNK Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды