Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1903

Страница: 1903 / 2244

STARTER INSPECTION [LF]

ON-VEHICLE INSPECTION

1. Verify that the battery is fully charged.

2. The starter is normal if it rotates smoothly and without any noise when the engine is cranked.



If the starter does not operate, inspect the following:



Remove the starter, and inspect the starter unit.



Inspect the related wiring harnesses, the ignition switch, and the transmission range switch
(AT).

NO-LOAD TEST

1. Verify that the battery is fully charged.

2. Connect the starter, battery and a tester as shown in

Fig. 6

3. Operate the starter and verify that it rotates smoothly.



If the starter does not rotate smoothly, inspect the starter unit.

4. Measure the voltage and current while the starter is operating.



If not within the specification, replace the starter.

Starter no load test voltage

11 V

Starter no load test current

90 A or less

2007 Mazda MX-5 Miata Sport

2007 ENGINE Starting System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:06:51 PM

Page 5

«
...
1901
1902
1903
1904
1905
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды