Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1149

Страница: 1149 / 2244

5. Follow the valve clearance adjustment procedure from 21 to 50 and install the intake camshaft and

variable valve timing actuator. (See

VALVE CLEARANCE ADJUSTMENT [LF]

OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION [LF]

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

3. Remove the plug hole plate. (See

PLUG HOLE PLATE REMOVAL/INSTALLATION [LF]

4. Remove the ignition coils. (See

IGNITION COIL REMOVAL/INSTALLATION [LF]

5. Remove the CMP sensor. (See

CAMSHAFT POSITION (CMP) SENSOR

REMOVAL/INSTALLATION [LF]

6. Remove the OCV connector.

Fig. 74: Identifying Oil Control Valve (OCV) [LF] (With Torque Specifications)

Courtesy of MAZDA MOTORS CORP.

7. Remove the ventilation hose. (See

QUICK RELEASE CONNECTOR (EMISSION SYSTEM)

REMOVAL/INSTALLATION [LF]

8. Remove the cylinder head cover. (See

CYLINDER HEAD COVER INSTALLATION NOTE

9. Remove in the order indicated in

Fig. 74

10. Install in the reverse order of removal.

2007 Mazda MX-5 Miata Sport

2007 ENGINE Mechanical - MX-5

Microsoft

Thursday, July 09, 2009 3:21:51 PM

Page 83

«
...
1147
1148
1149
1150
1151
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды