Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1420 | Manualshive

Страница: 1420 / 2244

background image

2007 HVAC

Refrigerant System - MX-5 Miata

REFRIGERANT SYSTEM SERVICE WARNINGS

USING/HANDLING UNAPPROVED REFRIGERANT



Using a flammable refrigerant, such as OZ-12, in this vehicle is dangerous. In an accident, the
refrigerant may catch fire, resulting in serious injury or death. When servicing this vehicle, use
only R-134a.



Checking for system leakage on a vehicle that has been serviced with flammable refrigerant, such
as OZ-12, is dangerous. Conventional leak detectors use an electronically generated arc which can
ignite the refrigerant, causing serious injury or death. If a flammable refrigerant may have been
used to service the system, or if you suspect a flammable refrigerant has been used, contact the
local fire marshal or EPA office for information on handling the refrigerant.

HANDLING REFRIGERANT



Avoid breathing air conditioning refrigerant or lubricant vapor. Exposure may irritate eyes, nose
and throat. Also, due to environmental concerns, use service equipment certified to meet the
requirements of SAE J2210 (R-134a recycling equipment) when draining R-134a from the air
conditioning system. If accidental system discharge occurs, ventilate work area before resuming
service.



Do not pressure test or leak test R-134a service equipment and/or vehicle air conditioning system
with compressed air. Some mixtures of air and R-134a have been shown to be combustible at
elevated pressures. These mixtures, if ignited, may cause injury or property damage. Additional
health and safety information may be obtained from refrigerant manufacturers.



Do not allow the refrigerant to leak near fire or any kind of heat. A poisonous gas may be
generated if the refrigerant gas contacts fire or heat such as from cigarettes and heaters. When
carrying out any operation that can cause refrigerant leakage, extinguish or remove the above-
mentioned heat sources and maintain adequate ventilation.



Handling liquid refrigerant is dangerous. A drop of it on the skin can result in localized frostbite.
When handling the refrigerant, wear gloves and safety goggles. If refrigerant splashes into the eyes,
immediately wash them with clean water and consult a doctor.

STORING REFRIGERANT



The refrigerant container is highly pressurized. If it is subjected to high heat, it could explode,
scattering metal fragments and liquid refrigerant that can seriously injure you. Store the
refrigerant at temperatures below 40°C {104°F}.

REFRIGERANT SYSTEM SERVICE CAUTIONS

HANDLING COMPRESSOR OIL

2007 Mazda MX-5 Miata Sport

2007 HVAC Refrigerant System - MX-5 Miata

2007 Mazda MX-5 Miata Sport

2007 HVAC Refrigerant System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:26:29 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Thursday, July 09, 2009 2:26:34 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
1418
1419
1420
1421
1422
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Mitsubishi Страницы: 160

Бренд: Cadillac Страницы: 442

Бренд: Alpine Страницы: 8

Бренд: Bestop Страницы: 11

Бренд: Whispbar Страницы: 14

2014 Insignia VXR SuperSport

Бренд: Vauxhall Страницы: 56

2016 Sandero Stepway

Бренд: Renault Страницы: 183

Бренд: Nav TV Страницы: 5

Ram Commercial2016

Бренд: Dodge Страницы: 675

Бренд: Mercedes-Benz Страницы: 91

Бренд: NavInc Страницы: 6

Denali 1094-0185-15

Бренд: E&G Classics Страницы: 3

Бренд: Metra Electronics Страницы: 2

2003 Silhouette

Бренд: Oldsmobile Страницы: 466

Бренд: Enduro Страницы: 52

Бренд: Oldsmobile Страницы: 358

Бренд: Westfalia Страницы: 10

Бренд: Mobileye Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды