Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1497 | Manualshive

Страница: 1497 / 2244

background image

INSTRUMENT CLUSTER INPUT/OUTPUT CHECK MODE

.)

Using M-MDS Or External Diagnostic Equipment

1. Connect the M-MDS to the DLC-2 connector.

2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.



When using the IDS (laptop PC)



Select the "Toolbox" tab.



Select "DataLogger".



Select "Module".



Select "IC".



When using the PDS (Pocket PC)



Select "Module Tests".



Select "IC".



Select "DataLogger".

CAUTION:



If the engine speed exceeds the allowable range, the engine could be
damaged. Therefore, when inspecting the tachometer, do not allow
the engine speed to exceed the allowable range indication on the
tachometer.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Instrumentation-Driver Info - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:30:27 PM

Page 9

© 2005 Mitchell Repair Information Company, LLC.

«
...
1495
1496
1497
1498
1499
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: UMBRA RIMORCHI Страницы: 18

Бренд: Honda Страницы: 32

Бренд: Toyota Страницы: 52

Бренд: Jeep Страницы: 380

Бренд: RAM Страницы: 496

Бренд: Bestop Страницы: 5

Бренд: PowerMadd Страницы: 3

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Бренд: Havis-Shields Страницы: 1

1995 Cutlass Supreme

Бренд: Oldsmobile Страницы: 340

Бренд: GReddy Страницы: 12

Бренд: BraunAbility Страницы: 46

Бренд: SAFARI Страницы: 5

Бренд: Axxess Страницы: 16

Бренд: Ranger design Страницы: 22

Бренд: BMW Страницы: 40

Бренд: Toyota Страницы: 285

Бренд: Porsche Страницы: 127

Бренд: Buick Страницы: 371

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды