manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1413 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1413

Fig. 12: Pouring Drained Oil From Old A/C Compressor Into New A/C Compressor

 

Courtesy of MAZDA MOTORS CORP.

 

CONDENSER REMOVAL/INSTALLATION 

1. Remove the battery cover.  

2. Disconnect the negative battery cable. (See 

BATTERY REMOVAL/INSTALLATION [LF]

 .)  

3. Discharge the refrigerant from the system. (See 

REFRIGERANT CHARGING

 .)  

4. Remove the splash shields.  

5. Remove the under cover.  

 

2007 Mazda MX-5 Miata Sport 

2007 HVAC Basic System - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:22:45 PM

Page 14 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов