Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2065

Страница: 2065 / 2244

(See

CLIMATE CONTROL UNIT INSPECTION

Throttle Position (TP) Sweep Inspection

1. Connect the M-MDS or equivalent to the DLC-2.

2. Turn the ignition switch to the ON position.

3. Verify that none of the following DTC are displayed:



P0122, P0123, P0222, P0223, P0638, P2101, P2107, P2108, P2109, P2112, P2119, P2122, P2123,
P2127, P2128, P2135, P2138



If any one DTC is displayed, perform DTC inspection.

4. Access TP_REL PID.

5. Verify that the PID reading is within the CTP value. (See

PCM INSPECTION [LF]



If the PID reading is out of range, perform the following:



Remove the air duct from the throttle valve body.



Verify that the throttle valve opens when the accelerator pedal is depressed.



If the throttle valve opens, inspect the throttle position sensor and related wiring
harness.



If the throttle valve does not open, inspect the throttle actuator control motor and
related wiring harness.

6. Gradually depress the throttle pedal and verify that the PID reading increases accordingly.



If the PID reading drops momentarily, inspect the following:



Throttle position sensor

7. Fully depress the throttle pedal and verify that the PID reading is within WOT value. (See

PCM

INSPECTION [LF]



If the PID reading is out of range, perform the followings:



Remove the air duct from throttle valve body.



Verify that the throttle valve opens when throttle pedal is depressed.



If the throttle valve opens, inspect the throttle position sensor and related wiring
harness.



If the throttle valve does not open, inspect the throttle actuator control motor and
related wiring harness.

VARIABLE INTAKE AIR CONTROL OPERATION INSPECTION

1. Start the engine.

2. Inspect the rod operation. (See

VARIABLE INTAKE AIR SHUTTER VALVE ACTUATOR

INSPECTION [LF]



If the rod operation is not as specified, inspect as follows:

1. Stop the engine.

2. Connect the M-MDS or equivalent to the DLC-2.

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:11 PM

Page 132

«
...
2063
2064
2065
2066
2067
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды