Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 260 | Manualshive

Страница: 260 / 2244

background image

Fig. 33: Aligning Mark On Clock Spring With Mark On Outer Housing

Courtesy of MAZDA MOTORS CORP.

CLOCK SPRING INSPECTION

1. Remove the driver-side air bag module. (See

DRIVER-SIDE AIR BAG MODULE

REMOVAL/INSTALLATION

.)

2. Remove the steering wheel. (See

STEERING WHEEL AND COLUMN

REMOVAL/INSTALLATION

.)

3. Remove the clock spring. (See

CLOCK SPRING REMOVAL/INSTALLATION

.)

4. Verify that the continuity is as indicated in

Fig. 34

.



If not as indicated in

Fig. 34

, replace the clock spring.

NOTE:



When the vehicle-side connector for the clock spring is
disconnected, terminals 1A, 1B, 1C and 1D are shorted to prevent
unexpected operation (deployment) of the air bag module.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 36

© 2005 Mitchell Repair Information Company, LLC.

«
...
258
259
260
261
262
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Suzuki Страницы: 16

Бренд: Ranger design Страницы: 6

Бренд: Abarth Страницы: 176

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

Бренд: FORM FIT Страницы: 2

Бренд: Chevrolet Страницы: 376

Бренд: Mazda Страницы: 15

DLD Wide Range II

Бренд: VDO Страницы: 84

TravelCharge Companion GO-Plus

Бренд: Wagan Страницы: 3

Бренд: Mercedes-Benz Страницы: 368

Бренд: TATA Motors Страницы: 236

Challenger 2013

Бренд: Dodge Страницы: 543

Бренд: Axxess Страницы: 8

Бренд: Dodge Страницы: 276

Бренд: Ecco Страницы: 24

Бренд: Thule Страницы: 4

CERTA CTCVINCVR14A

Бренд: Kogan Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды