Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1619

Страница: 1619 / 2244

Lock/unlock
input

Driver-side
door key
cylinder switch

cylinder is locked

2.5



Driver-side
door key
cylinder switch



Related wiring
harnesses

At the moment key
cylinder is unlocked

1.0 or less

At the moment key
cylinder is neutral
position

Unlock signal
input

Door lock-link
switch (driver-
side)

Driver-side door is
unlocked: Inspect for
continuity to ground.

Continuity
detected

Door lock-link
switch (driver-side)

Driver-side door is
locked: Inspect for
continuity to ground.

No continuity

Unlock input
(trunk lid)

Trunk key
cylinder switch

At the moment key
cylinder is unlocked

1.0 or less



Trunk key
cylinder switch



Related wiring
harnesses

At the moment key
cylinder is neutral
position

Hazard output

Hazard
warning light

Press the LOCK button
(transmitter)

B+ <-- 1.0 or
less<--B+



Hazard
warning light



Related wiring
harnesses

Press the UNLOCK
button (transmitter)

B+ <-- 1.0 or
less<--B+<--
1.0 or less<--
B+

Other

B+

Trunk open
output

Trunk opener
relay

Press the trunk open
switch

1.0 or less



Trunk opener
relay



Related wiring
harnesses

Other

B+

Door switch
signal (RH)
output

Door switch

Door open (RH) (Door
switch on)

1.0 or less



Door switch
(RH)



Related wiring
harnesses

Door closed (RH)
(Door switch off)

B+

Unlock signal
input

Door lock-link
switch
(passenger-
side)

Passenger-side door is
unlocked: Inspect for
continuity to ground.

Continuity
detected

Door lock-link
switch (passenger-
side)

Passenger-side door is
locked: Inspect for
continuity to ground.

No continuity

Serial
communication

Power window
main switch

Because this terminal is
for communication,
good/no good judgment
by terminal voltage is
not possible.



Power window
main switch



Related wiring
harnesses

Door open (LH) (Door

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Keyless Entry System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:35:24 PM

Page 20

«
...
1617
1618
1619
1620
1621
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды