Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1431 | Manualshive

Страница: 1431 / 2244

background image

Fig. 11: Installing Caps To Charging Valves

Courtesy of MAZDA MOTORS CORP.

REFRIGERANT RECOVERY

1. Connect an R-134a recovery/recycling/recharging device to the vehicle and follow the device

manufacturer's instructions.

REFRIGERANT PRESSURE CHECK

1. Connect the manifold gauge.

2. Start the engine and arrow it to reach operating temperature.

3. During pressure check, run the engine at a constant

1,500 rpm

.

4. Set the fan speed MAX-HI.

WARNING:



Avoid breathing air conditioning refrigerant or lubricant vapor.
Exposure may irritate eyes, nose and throat. Also, due to
environmental concerns, use service equipment certified to meet the
requirements of SAE J2210 (R-134a recycling equipment) when
draining R-134a from the air conditioning system. If accidental
system discharge occurs, ventilate work area before resuming
service.

2007 Mazda MX-5 Miata Sport

2007 HVAC Refrigerant System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:26:29 PM

Page 12

© 2005 Mitchell Repair Information Company, LLC.

«
...
1429
1430
1431
1432
1433
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Jabra Страницы: 2

Бренд: Jabra Страницы: 38

Бренд: U & Me Brothers Страницы: 6

Бренд: Toyota Страницы: 52

Бренд: Condor Страницы: 2

DLD Wide Range II

Бренд: VDO Страницы: 84

TravelCharge Companion GO-Plus

Бренд: Wagan Страницы: 3

DELTA DL FIX 209FP

Бренд: Menabo Страницы: 8

Бренд: Hank Страницы: 2

Бренд: travall Страницы: 2

Бренд: Gacell Страницы: 12

JEEP GL ADIATOR JT TOPPER ROOF RACK

Бренд: JCROffroad Страницы: 7

IVH-9000-2R440Q

Бренд: Vecow Страницы: 110

Бренд: POOL-LINE Страницы: 2

Бренд: TATA Motors Страницы: 151

QUICKDRAW RACHET TIE-DOWNS 855

Бренд: Thule Страницы: 3

Бренд: Gacell Страницы: 25

Бренд: Goobay Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды