Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2120 | Manualshive

Страница: 2120 / 2244

background image

Fig. 54: Removing Clip D

Courtesy of MAZDA MOTORS CORP.

REAR WINDOW GLASS INSTALLATION NOTE

Rear window glass or middle roof panel is newly replaced

1. Adjust the rear window glass and middle roof panel gap and height difference so that it is within the

specification. (See

POWER RETRACTABLE HARDTOP ADJUSTMENT

.)

Rear window glass or middle roof panel is reused

1. Install the shim according to the number verified prior to removal.

2. Align the alignment marks applied before the rear window glass removal, install the rear window glass,

and then remove the masking tape.

3. Refer to POWER RETRACTABLE HARDTOP ADJUSTMENT and verify that the gap and height

difference between the rear window glass and middle roof panel are within the specifications. Adjust the
power retractable hardtop if necessary. (See

POWER RETRACTABLE HARDTOP

ADJUSTMENT

.)

REAR WINDOW DEFROSTER FILAMENT INSPECTION

1. Turn the ignition switch to the ON position.

2. Turn the rear window defroster switch on.

CAUTION:



Directly touching the rear window defroster filament with the
lead of the voltmeter could damage it. Wrap aluminum foil
around the end of the lead and test the rear window defroster
filament by touching it with the foil.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:32 PM

Page 35

© 2005 Mitchell Repair Information Company, LLC.

«
...
2118
2119
2120
2121
2122
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: GMC Страницы: 140

WrapAround Windjammer

Бренд: Bestop Страницы: 7

Бренд: Audi Страницы: 9

Бренд: Belkin Страницы: 4

Бренд: Flash Cover Страницы: 2

Бренд: Porsche Страницы: 98

Бренд: RHOX Страницы: 8

Бренд: Atera Страницы: 3

Бренд: Black Horse Страницы: 5

1500 CLASSIC 2020

Бренд: RAM Страницы: 360

Бренд: Volvo Страницы: 18

Бренд: ULTIMATE SPEED Страницы: 26

Бренд: Westfalia Страницы: 2

Бренд: Metra Electronics Страницы: 10

Бренд: Saab Страницы: 498

Бренд: Kuda-Phonebase Страницы: 6

Бренд: Volkswagen Страницы: 2

Бренд: ACV Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды