Siemens siprotec 7SA6, Manual

Page: 873 / 876

Index
Index-7
7SA6 Manual
C53000-G1176-C156-2
Sequence of a single and three-pole interrupt
cycle
6-194
Sequence of a single-pole interrupt cycle
6-194
Sequence of a three-pole reclose cycle
6-193
Serial Interfaces
1-3, 5-54, 8-16
Service Conditions
10-12
Service Interface
1-7
Set Status
7-52
Setting Groups
6-14
Setting groups
Changeover
8-10
Settings
4-4
Settings for Contact Chatter Blocking
5-37
Shock and vibration
10-11
Short Circuit Links
A-10
Signal idle state
5-56
Signal Transmission
Channels
6-90, 6-139
for Internal and External Remote Tripping
8-74
SIMATIC CFC 4
A-12
Singe point indication
5-21
Single-Pole Tripping
6-297
Single-Pole Tripping with Two-Phase Faults
6-298
Single-stage breaker failure protection
6-261
SIPROTEC 4 Devices
4-1
Software–Monitoring
6-276
Source
5-19
Special Cases
5-3
Spontaneous Messages
6-296, 7-6, 7-12
Standard Interlocking
6-321
Starting Conditions
6-242
Statistics
10-46
Storage
3-12
Stub Protection
6-166, 6-174, 10-32
Summation Monitoring
6-287
Supplementary Functions
6-306, 10-44
Switching
onto a Dead Fault
6-167
Switching Authority
7-56
Switching between Setting Groups
6-15
Switching Mode
7-57
Switching On and Off
6-140
Switching onto a Dead Earth Fault
6-134
Switching onto a Dead Fault
6-48
Switching onto an Earth Fault
6-127
Switching Statistics
6-302
Symmetry Monitoring
6-287
Synchronism check conditions
before automatic reclosure
6-222
before manual closing
6-222
Synchronization and Voltage Check
1-11
System (SCADA) Interface
8-41, 10-7
system interface
1-7
System Starpoint
6-10
T
Tagging
4-16, 7-55
Technical Data
10-1
Teleprotection
Methods
6-139
with Distance Protection
8-69
with Earth Fault Protection
6-133
Teleprotection Methods
6-89
Teleprotection Schemes with Distance Protection
6-89
Teleprotection Supplement
1-9
Teleprotection with Earth Fault Protection
8-72
Terminal Block Covering Caps
A-10
Terminal Blocks
2-29
Termination variants
8-9
Test Messages to the System (SCADA) Interface
during Test Operation
7-36
Testing of the Teleprotection System
8-69
Testing User-Defined Functions
8-74
Text Values
6-3, 6-5
The Earth Fault Detection in Non-earthed
Systems
6-180
Three-pole Coupling
6-23
Three-Pole Tripping
6-297
Time
Status
7-28
Synchronization
5-58
Time Delayed Overcurrent Protection
1-11
Time Settings
6-116, 6-152
Time Synchronization
1-4, 10-8
Time Synchronization Interface
8-42
Transfer trip to the remote end circuit breaker
6-257
Transferring Metering Values
5-36
Transient Blocking
6-112, 6-116, 6-148,
6-153
Triggering Oscillographic Recordings
8-75
Triggering with DIGSI® 4
8-76
Trip and Close Test with the Circuit Breaker
8-75
Trip Circuit Supervision
6-281, 6-288, 10-42
Trip Dependent Messages
6-302
Trip Log (Fault Messages)
7-6
Trip/Close Command Duration
6-11
Tripping Logic
6-70
Tripping Logic of the Distance Protection
Applying the Function Parameter Settings
6-71