Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 947 | Manualshive

Page: 947 / 1426

background image

CPM Interrupt Controller

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

35-3

The only true SDMA interrupt source is the SDMA channel bus error entry that is reported when a bus
error occurs during an SDMA access. Other SDMA-related interrupts are reported through each individual
USB, SCC, SMC, SPI, or I

2

C channel. USB and SCCs interrupts can be reprioritized as described in the

next two sections.

35.2.1

Programming Relative Priority (Grouping and Spreading)

The relative priority between the USB and the 3 SCCs is programmable dynamically through
CICR[SCnP], shown in

Table 35-3

.

Table 35-1

has no explicit entry for USB and SCCs because the entries

can be mapped to any of these locations. This is programmed in the CICR (see

Table 35-3

).

SCC entries can be grouped or spread by clearing or setting CICR[SPS], respectively; SPS cannot be
changed dynamically. These options are described as follows:

•

If SPS = 1, the USB and 3 SCCs are grouped at the top of the priority table, ahead of most other
CPM interrupt sources. Grouping is useful where the USB and 3 SCCs function at a very high data
rate and interrupt latency is critical.

Table 35-1. Prioritization of CPM Interrupt Sources

Priority

Source Description

Multiple

Events

Priority

Source Description

Multiple

Events

0x1F

(Highest)

Parallel I/O–PC15

1

1

Port C interrupts (external sources) are described in

Section 34.4.1.5, “Port C Interrupt Control Register (PCINT).”

No

0x0F

Parallel I/O–PC11

1

No

0x1E

SCCa

2

(grouped and spread)

2

USB and SCCs can be programmed to any of these locations. Group and spread are described in

Section 35.2.1,

“Programming Relative Priority (Grouping and Spreading).”

Yes

0x0E

Parallel I/O–PC10

1

No

0x1D

SCCb

2

(grouped) Yes

0x0D

SCCc

2

(spread)

Yes

0x1C

SCCc

2

(grouped)

Yes

0x0C

Timer3

Yes

0x1B

SCCd

2

(grouped)

Yes

0x0B

Parallel I/O–PC9

1

No

0x1A

Parallel I/O–PC14

1

No

0x0A

Parallel I/O–PC8

1

No

0x19

Timer 1

Yes

0x09

Parallel I/O–PC7

1

No

0x18

Parallel I/O–PC13

1

No

0x08

SCCd

2

(spread)

Yes

0x17

Parallel I/O–PC12

1

No

0x07

Timer4

Yes

0x16

SDMA channel bus error

Yes

0x06

Parallel I/O–PC6

1

No

0x15

IDMA1

Yes

0x05

SPI

Yes

0x14

IDMA2

Yes

0x04

SMC1

Yes

0x13

SCCb

2

(spread)

Yes

0x03

SMC2/PIP

Yes

0x12

Timer 2

Yes

0x02

Parallel I/O–PC5

1

No

0x11

RISC timer table

Yes

0x01

Parallel I/O–PC4

1

No

0x10

I

2

C

Yes

0x00

(Lowest)

Reserved

—

«
...
945
946
947
948
949
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Aaeon Pages: 100

Brand: Aaeon Pages: 120

Brand: Aaeon Pages: 116

Brand: Aaeon Pages: 119

Brand: Aaeon Pages: 111

Brand: Aaeon Pages: 106

Brand: Aaeon Pages: 48

Brand: Aaeon Pages: 44

Brand: IEI Technology Pages: 211

Brand: IEI Technology Pages: 8

Brand: IEI Technology Pages: 8

TI GE PHY HSMC CARD

Brand: Macnica Pages: 16

Brand: Ampro Pages: 72

Brand: Intertec Components Pages: 3

Brand: Sun Microsystems Pages: 74

Brand: Telit Wireless Solutions Pages: 5

Brand: ST Pages: 13

Brand: ASROCK Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands