Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 1267 | Manualshive

Page: 1267 / 1426

background image

System Development and Debugging

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

53-17

•

Greater than or equal of the smallest unsigned number (0000...0).

•

Less than or equal of the maximum positive number in signed mode (0111...1).

•

Greater than or equal of the maximum negative number in signed mode (1000...).

These boundary cases do not require special support because they are considered always true. They can be
programmed using the ignore option of the load/store watchpoint programming. See

Section 53.5.1.5,

“Load/Store Support AND-OR Control Register (LCTRL2).”

53.2.5

Load/Store Breakpoint Example

CMPE and CMPF are used for load/store addresses while CMPG and CMPH are used for load/store data.

The procedure is as follows:

1. Write the value in the appropriate comparator register, CMPE, CMPF, CMPG, or CMPH.

2. For load/store data, program the operand size in LCTRL1[CSx] and the byte mask in

LCTRL1[CxBMSK].

3. Write the comparison type in LCTRL1[CTx]. For load/store data, program whether the operand is

signed or unsigned LCTRL1[SUSx].

4. Select a watchpoint enable event:

— Define the load/store watchpoint event in LCTRL2[LWxLA] or LCTRL2[LWxLD]

— Enable the address or data event in LCTRL2[LWxLADC] or LCTRL2[LWxLDDC]

5. Disable instruction events affecting load/store watchpoints—Clear LWxIADC (LWxIA is a don’t

care).

6. Enable the watchpoint in LCTRL2[LWxEN].

7. Enable a trap on every watchpoint or every N watchpoints.

Option: Enable trap on every load/store watchpoint in LCTRL2[SLWxEN] or on every N
watchpoints in COUNTx. (Set CNTV to n and select the load/store watchpoint in CNTC).

8. Select whether breakpoints are maskable or nonmaskable in LCTRL2[BRKNOMSK].

9. Optionally select whether a load/store trap causes the debug mode to be entered in

DER[LBRKE].

53.3

Development System Interface

It is often useful to debug a target system without making changes. However, sometimes it is impossible
to add load to the lines connected to the existing system without disrupting its operation. The development
system interface of the core enables debug of a target system with minimal cost and intrusiveness.

The development system interface of the core uses the development port, which is a dedicated serial port
and, therefore, does not need any of the regular system interfaces.

The development port is a relatively inexpensive interface that allows a development system to operate in
a lower frequency than the core’s frequency and controls system activity when the core is in debug mode.

«
...
1265
1266
1267
1268
1269
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Yamaha Pages: 82

Kontron mITX-CFL-S

Brand: S&T Pages: 8

Brand: Xilinx Pages: 56

Brand: Shuttle Pages: 81

Brand: Gigabyte Pages: 80

TB360-BTC PRO 2.0

Brand: Biostar Pages: 59

Brand: EPOX Pages: 68

Brand: IEI Technology Pages: 21

Brand: ASROCK Pages: 18

TAS5508-5142K7EVM

Brand: Texas Instruments Pages: 20

Chipset TRF2436EVM

Brand: Texas Instruments Pages: 11

Brand: Supero Pages: 80

Brand: ECS Pages: 60

Supero C9X299-PG300F

Brand: Supermicro Pages: 28

Brand: CyberResearch Pages: 286

Brand: DFI Pages: 102

Brand: DFI Pages: 98

Brand: DFI Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands