Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 1102 | Manualshive

Page: 1102 / 1426

background image

AAL2 Implementation

MPC885 PowerQUICC Family Reference Manual, Rev. 2

44-12

Freescale Semiconductor

44.4.5.1.1

Starting the Timer for a Partially-Filled Active Buffer

When the AAL2 is unable to fill a channel’s active buffer, it does the following:

•

Starts the count down for the channel’s partially filled active buffer by setting the
AAL2_TxWait_table[X,Y] bit, where:

X = (TCU + AAL2_TxWait_PTR) modulo (the number of rows in the wait table)

Y = channel number.

•

Stores X in the channel’s AAL2_TCT (so that it can later clear the bit once the active buffer is sent,
either full or partially filled).

The TCU field is defined in AAL2_TCT of each channel. The wait pointer (AAL2_TxWait_PTR) is
defined in the AAL2 parameter RAM area; see

Section 44.7.1, “AAL2 Parameter RAM.”

44.4.5.1.2

Countdown Mechanism and Detection of Expired Buffers

Each advance of the wait pointer through the rows of the wait table corresponds to one RISC timer tick.
The wait pointer marks the current row in the wait table. All bits that are set in the current row represent
expired channels. Each time the RISC timer expires, it asserts a request to the CPM. This request in turn
activates AAL2 to do the following:

•

For each bit set in the current row, the AAL2 will:

— Pad the partially filled active buffer with zeros.

— Close its BD (R=1). (The cell is sent the next time the channel is scheduled by the APC or the

host issues an

APC

BYPASS

command for the channel.)

— Clear the channel’s bit in the wait table.

•

The wait pointer advances to the next row of the wait table, thereby decreasing the wait time of all
remaining partially filled active buffers by one RISC timer tick.

When the wait pointer reaches the end of the table, it advances back to the beginning. The size of the wait
table is limited to 256 rows, which means that the maximum delay of an active buffer is (255 * RISC timer
period).

Note that if all the bits in the current row are 0 (which may happen in most cases), AAL2 simply advances
the wait pointer. All channels in the wait table then become one row closer to the wait pointer, which means
that one RISC timer period is subtracted from the wait time of all the partially filled active buffers.

The host controls the count down mechanism in each channel’s AAL2_TCT:

•

AAL2_TCT[ET] defines whether the Timer CU mechanism for this channel is enabled.

•

AAL2_TCT[TCU] determines the maximum delay for the channel’s partially filled active buffer
(TCU * RISC timer period).

For example, assuming the following:

•

RISC timer expires every 0.5 ms,

•

TCU = 6 (for channel n), and

•

AAL2_TxWait_PTR points to row 3,

«
...
1100
1101
1102
1103
1104
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: ASROCK Pages: 5

Brand: Texas Instruments Pages: 22

Brand: Waveshare Pages: 72

Brand: ST Pages: 9

Brand: JETWAY Pages: 39

Brand: JETWAY Pages: 44

Brand: Sundance Spas Pages: 21

Brand: Erreka Pages: 4

MT9V113PACSTCH-GEVB

Brand: ON Semiconductor Pages: 5

EV MOD CH101-01-02

Brand: TDK Pages: 10

Brand: California Eastern Laboratories Pages: 34

Brand: Gigabyte Pages: 72

Brand: STMicroelectronics Pages: 17

Brand: ASROCK Pages: 153

Brand: Suzuki Marine Pages: 63

Brand: DFI-ITOX Pages: 129

Brand: Cytron Pages: 30

G41MH/USB3 R2.0

Brand: ASROCK Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands