Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 779 | Manualshive

Page: 779 / 1426

background image

SCC Ethernet Mode

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

27-23

26. Initialize the TxBD and assume the Tx data frame is at 0x0000_2000 in main memory and contains

fourteen 8-bit characters (destination and source addresses plus the type field). Write 0xFC00 to
TxBD[Status and Control], add PAD to the frame and generate a CRC. Then write 0x000E to
TxBD[Data Length] and 0x0000_2000 to TxBD[Buffer Pointer].

27. Write 0xFFFF to the SCCE register to clear any previous events.

28. Write 0x001A to the SCCM register to enable the TXE, RXF, and TXB interrupts.

29. Write 0x8000_0000 to the CIMR so that SCC2 can generate a system interrupt. The CICR register

should also be initialized.

30. Write 0x0000_0000 to GSMR_H2 to enable normal operation of all modes.

31. Write 0x1088_000C to the GSMR_L2 register to configure CTS (CLSN) and CD (RENA) to

automatically control transmission and reception (DIAG bits) and the ethernet mode. TCI is set to
allow more setup time for the EEST to receive the MPC885 transmit data. TPL and TPP are set for
ethernet requirements. The DPLL is not used with ethernet. Note that the ENT and ENR are not
enabled yet.

32. Write 0xD555 to the DSR.

33. Set the PSMR2 to 0x0A0A to configure 32-bit CRC, promiscuous mode, and begin searching for

the start frame delimiter 22 bits after RENA.

34. Enable the TENA pin (RTS). Since GSMR[MODE] are written to ethernet, the TENA signal is

low. Set PCPAR[14] and clear PCDIR[14].

35. Write 0x1088_003C to GSMR_L2 to enable the SCC2 transmitter and receiver. This additional

write ensures that ENT and ENR are enabled last.

After 14 bytes and the 46 bytes of automatic pad (plus the 4 bytes of CRC) are sent, the TxBD is closed.
Additionally, the receive buffer is closed after a frame is received. Any data received after 1520 bytes or
a single frame causes a busy (out-of-buffers) condition because only one RxBD is prepared.

«
...
777
778
779
780
781
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Aaeon Pages: 122

Brand: Aaeon Pages: 52

Brand: Aaeon Pages: 99

Brand: ASROCK Pages: 126

Brand: DFI Pages: 104

Brand: AOpen Pages: 8

Brand: C-Control Pages: 8

Strata Enabled NCV6357

Brand: ON Semiconductor Pages: 6

Brand: IBASE Technology Pages: 56

H470 AORUS PRO AX

Brand: Gigabyte Pages: 52

Brand: JETWAY Pages: 45

Brand: Engbo Pages: 64

Brand: Advantech Pages: 104

E-TEC 40RL 2008

Brand: Evinrude Pages: 58

Brand: Daewoo Pages: 39

Brand: Gigabyte Pages: 53

Brand: IEI Technology Pages: 12

Brand: Texas Instruments Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands