manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Reference Manual

The Freescale Semiconductor PowerQUICC MPC870 is a powerful and versatile processing unit designed for high-performance embedded applications. With its comprehensive Reference Manual available for free download, users can easily access in-depth information and instructions on maximizing the product's capabilities. Visit manualshive.com to obtain your free manual today.

Share
Download
background image

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

50-1

 

Chapter 50  
SEC Lite Crypto-Channel

The crypto-channel manages data associated with one of more execution units (EUs) in the SEC Lite. 
Control and data information for a given task is stored in the form of sixteen 32-bit word descriptors in 
system memory or in the crypto-channel itself. The descriptor describes how the EU should be initialized, 
where to fetch the data to be ciphered and where to store the ciphered data the EU outputs. Through a series 
of requests to the controller, the crypto-channel decodes the contents of the descriptors to perform the 
following functions:

•

Request assignment of one or more of the several EUs in the SEC Lite for use by the channel.

•

Automatically initialize mode registers in the assigned EU upon notification of completion of the 
EU reset sequence.

•

Transfer data packets (up to 32 Kbytes) from system memory (Master Read) into assigned EU 
input registers and FIFOs (EU Write).

•

Transfer data packets (up to 32 Kbytes) from assigned EU output registers and FIFOs (EU Read) 
to system memory space (Master Write).

•

Automatically initialize the key size register in the assigned EU after requesting a write to EU key 
address space.

•

Automatically initialize data size register in the assigned EU before requesting a write to EU FIFO 
address space.

•

Automatically initialize the EU_GO register (where applicable) in the assigned EU upon 
completion of last EU write indicated by the descriptor. The channel will wait for a indication from 
the EU that processing of input data is complete before proceeding with further activity after 
writing EU_GO.

•

Request assignment of the MDEU when the descriptor header calls for multi-operation processing. 
The MDEU will be configured to snoop input or output data intended for the primary assigned EU. 

•

Reset assigned EU(s).

•

Release assigned EU(s).

•

Automatically fetch the next descriptor from system memory and start processing, when chaining 
is enabled. Descriptor chains can be of unlimited size

•

Provide feedback to host, via interrupt, when a descriptor, or a chain of descriptors, has been 
completely processed.

•

Provide feedback to host, via modified descriptor header write back to system memory, when a 
descriptor, or a chain of descriptors, has been completely processed.

•

Provide feedback to host, via interrupt, when descriptor processing is halted due to an error.

The channel will wait indefinitely for the controller to complete a requested activity before continuing to 
process a descriptor.

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Analog Devices DC2837A-A Demo Manual preview
DC2837A-A
Brand: Analog Devices Pages: 8
Biostar P43D3 - BIOS Setup Manual preview
P43D3 - BIOS
Brand: Biostar Pages: 47
C&T Solution CT-DWL01 User Manual preview
CT-DWL01
Brand: C&T Solution Pages: 84
Diamond Systems Venus VNS563-4GD Manual preview
Venus VNS563-4GD
Brand: Diamond Systems Pages: 43
Freescale Semiconductor DEMO908GZ60 Quick Start Manual preview
DEMO908GZ60
Brand: Freescale Semiconductor Pages: 4
Aaeon IMBA-Q77 Operation User'S Manual preview
IMBA-Q77
Brand: Aaeon Pages: 119
Atmel SAM9N12/CN11-EK User Manual preview
SAM9N12/CN11-EK
Brand: Atmel Pages: 69
BESTEK BNX-M67 Quick Manual preview
BNX-M67
Brand: BESTEK Pages: 13
Linear Technology DC1928A Demo Manual preview
DC1928A
Brand: Linear Technology Pages: 6
MSI MS-6728 Manual preview
MS-6728
Brand: MSI Pages: 126
MSI MS-7760 Manual preview
MS-7760
Brand: MSI Pages: 90
J&W X48 Series User Manual preview
X48 Series
Brand: J&W Pages: 42
Wolfson WM8761-EV1M User Handbook Manual preview
WM8761-EV1M
Brand: Wolfson Pages: 12
IMS LCIC-BAT Re)Programming Manual preview
LCIC-BAT
Brand: IMS Pages: 14
AZZA KT33-BV Manual preview
KT33-BV
Brand: AZZA Pages: 48
GOWIN DK-START-GW1NR9 User Manual preview
DK-START-GW1NR9
Brand: GOWIN Pages: 38
Analog Devices EVAL-AD7761FMCZ User Manual preview
EVAL-AD7761FMCZ
Brand: Analog Devices Pages: 17
Procomp B687 Manual preview
B687
Brand: Procomp Pages: 46

Brands by name

Popular brands

Load more brands