manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Reference Manual

The Freescale Semiconductor PowerQUICC MPC870 is a powerful and versatile processing unit designed for high-performance embedded applications. With its comprehensive Reference Manual available for free download, users can easily access in-depth information and instructions on maximizing the product's capabilities. Visit manualshive.com to obtain your free manual today.

Share
Download
background image

SCC UART Mode

MPC885 PowerQUICC Family Reference Manual, Rev. 2

22-10

Freescale Semiconductor

 

Table 22-5

 describes TOSEQ fields.

22.12 Sending a Break (Transmitter)

A break is an all-zeros character with no stop bit that is sent by issuing a 

STOP

 

TRANSMIT

 command. The 

SCC finishes transmitting outstanding data, sends a programmable number of break characters 
(determined by BRKCR), and reverts to idle or sends data if a 

RESTART

 

TRANSMIT

 command is given 

before completion. When the break code is complete, the transmitter sends at least one high bit before 
sending more data, to guarantee recognition of a valid start bit. Because break characters do not preempt 
characters in the transmit FIFO, they may not be sent for four (SCC2–SCC4) character times. To reduce 
this latency, set GSMR_H[TFL] to decrease the FIFO size to one character before enabling the transmitter.

22.13 Sending a Preamble (Transmitter)

Sending a preamble sequence of consecutive ones ensures that a line is idle before sending a message. If 
the preamble bit TxBD[P] is set, the SCC sends a preamble sequence (idle character) before sending the 
buffer. For example, for 8 data bits, no parity, 1 stop bit, and 1 start bit, a preamble of 10 ones is sent before 
the first character in the buffer.

0

1

2

3

4

5

6

7

8

15

Field

—

REA

I

CT

—

A

CHARSEND

Reset

0000_0000_0000_0000

R/W

R/W

Addr

SCC base + 0x4E

Figure 22-4. Transmit Out-of-Sequence Register (TOSEQ)

Table 22-5. TOSEQ Field Descriptions

Bit

Name

Description

0–1

—

Reserved, should be cleared.

2

REA

Ready. Set when the character is ready for transmission. Remains 1 while the character is being 
sent. The CP clears this bit after transmission.

3

I

Interrupt. If this bit is set, transmission completion is flagged in the event register (SCCE[TX] is 
set), triggering a maskable interrupt to the core.

4

CT

Clear-to-send lost. Operates only if the SCC monitors CTS (GSMR_L[DIAG]). The CP sets this 
bit if CTS negates when the TOSEQ character is sent. If CTS negates and the TOSEQ character 
is sent during a buffer transmission, the TxBD[CT] status bit is also set.

5–6

—

Reserved, should be cleared.

7

A

Address. Setting this bit indicates an address character for multidrop mode.

8–15

CHARSEND

Character send. Contains the character to be sent. Any 5- to 8-bit character value can be sent 
in accordance with the UART configuration. The character should be placed in the lsbs of 
CHARSEND. This value can be changed only while REA = 0.

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Acrosser Technology AR-B104D Quick Manual preview
AR-B104D
Brand: Acrosser Technology Pages: 7
Texas Instruments LMR36506RREVM User Manual preview
LMR36506RREVM
Brand: Texas Instruments Pages: 16
Ublox EVK-NINA-B4 User Manual preview
EVK-NINA-B4
Brand: Ublox Pages: 38
MSI 645 Ultra Manual preview
645 Ultra
Brand: MSI Pages: 71
Watski 105761 Operating Instructions Manual preview
105761
Brand: Watski Pages: 43
Caji PROM8908 Operation Manuals preview
PROM8908
Brand: Caji Pages: 19
Quectel NB-IoT Module Series User Manual preview
NB-IoT Module Series
Brand: Quectel Pages: 31
Texas Instruments TAS6422E-Q1 User Manual preview
TAS6422E-Q1
Brand: Texas Instruments Pages: 35
Thinklabs UNIBOARD V1.1 User Manual preview
UNIBOARD V1.1
Brand: Thinklabs Pages: 129
BESTEK BNX-M67 Quick Manual preview
BNX-M67
Brand: BESTEK Pages: 13
Linear Technology DC1928A Demo Manual preview
DC1928A
Brand: Linear Technology Pages: 6
Liantec ITX-QM77 Quick Installation Manual preview
ITX-QM77
Brand: Liantec Pages: 4
ASROCK Z87 Extreme9/ac User Manual preview
Z87 Extreme9/ac
Brand: ASROCK Pages: 116
YASKAWA ANTAIOS User Manual preview
ANTAIOS
Brand: YASKAWA Pages: 28
Xilinx XtremeDSP Spartan-3A DSP 3400A... User Manual preview
XtremeDSP Spartan-3A DSP 3400A...
Brand: Xilinx Pages: 50
Texas Instruments TRS3221RGTEVM User Manual preview
TRS3221RGTEVM
Brand: Texas Instruments Pages: 13
Sleipner SX35 Installation Manual preview
SX35
Brand: Sleipner Pages: 24
Supero Supero X9DRW-7TPF User Manual preview
Supero X9DRW-7TPF
Brand: Supero Pages: 119

Brands by name

Popular brands

Load more brands