manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Reference Manual

The Freescale Semiconductor PowerQUICC MPC870 is a powerful and versatile processing unit designed for high-performance embedded applications. With its comprehensive Reference Manual available for free download, users can easily access in-depth information and instructions on maximizing the product's capabilities. Visit manualshive.com to obtain your free manual today.

Share
Download
background image

Instruction and Data Caches

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

7-23

 

MD_CTR[CIDEF]; and the entire memory space defaults to the guarded attribute. See 

Chapter 8, 

“Memory Management Unit,”

 for more information.

A data cache access begins with a load or store request from the load/store unit (LSU) in the core. The data 
cache has a 32-bit data path to and from the load/store unit, allowing for a 4-byte transfer per cycle. As 
shown in 

Figure 7-2

, bits 20–27 of the data address provide the index to select a set (0–255) within the data 

cache array. The tags from both ways of the set are compared against bits 0–19 of the data address. If a 
match is found and the matched entry is valid, it is a cache hit. If neither tag matches or the matched tag 
is not valid, it is a cache miss. 

The data cache operates in both write-through and write-back modes as programmed by the memory/cache 
access attributes. These modes affect store hit and store miss behavior of the data cache. Load hits and load 
misses behave the same regardless of the write-through/write-back mode. If two logical blocks map to the 
same physical block, it is considered a programming error for them to specify different cache write 
policies.

Each data cache block contains two state bits that implement a three-state 
(modified-valid/unmodified-valid/invalid) protocol. The MPC885 does not support snooping of the data 
cache. All memory is considered to have memory coherency not required attributes. Therefore, software 
must maintain data cache coherency. The MPC885 does not provide support for snooping external bus 
activity. All coherency between the internal caches and external agents (memory or I/O devices) must be 
controlled by software. In addition, there is no mechanism provided for DMA or other internal masters to 
access the data cache directly.

The MPC885 data cache includes the following operational features:

•

Single-cycle cache access on hit and one clock latency added for miss

•

The data cache supports hits under load misses.

•

1-word store buffer

•

Store misses bypass the data cache (no-allocate store miss) in write-through mode

•

4-word copyback buffer holds replaced modified cache blocks until they can be written to memory

•

Cache operation is blocked until the cache block is written to the cache array for store misses in 
write-back mode, 

•

The data cache supports the sync instruction through a cache pipe clean indication to the core.

7.6.1

Data Cache Load Hit

In the case of a data cache load hit, the requested word is transferred to the load/store unit. The LRU state 
of the set is updated, but the state bits remain unchanged.The access time for a data cache load hit is one 
clock cycle (that is, zero wait states).

7.6.2

Data Cache Read Miss

In the case of a data cache load miss, a block in the cache array is selected to receive the data from memory. 
The selection algorithm gives first priority to invalid blocks. If both blocks in the set are marked invalid, 
the block in way 0 is selected. If neither of the two blocks in the selected set are invalid, the least recently 

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Yamaha F80A Owner'S Manual preview
F80A
Brand: Yamaha Pages: 76
Yanmar SD60 Operation Manual preview
SD60
Brand: Yanmar Pages: 44
Procomp BVD2A Manual preview
BVD2A
Brand: Procomp Pages: 55
Xilinx SP601 User Manual preview
SP601
Brand: Xilinx Pages: 55
Biostar TA760G3 Setup Manual preview
TA760G3
Brand: Biostar Pages: 63
Renesas RTA-FoUSB-MON User Manual preview
RTA-FoUSB-MON
Brand: Renesas Pages: 30
CAME ZBKE Manual preview
ZBKE
Brand: CAME Pages: 8
DFI CS636-C246 User Manual preview
CS636-C246
Brand: DFI Pages: 73
JETWAY NF18GF User Manual preview
NF18GF
Brand: JETWAY Pages: 45
TDK SmartSound One User Manual preview
SmartSound One
Brand: TDK Pages: 11
JETWAY S446R2A User Manual preview
S446R2A
Brand: JETWAY Pages: 54
Outboards Group 2.2A Owner'S Manual preview
2.2A
Brand: Outboards Group Pages: 44
C&T Solution CT-PBT01 Series User Manual preview
CT-PBT01 Series
Brand: C&T Solution Pages: 48
BCM RX35Q User'S Quick Start preview
RX35Q
Brand: BCM Pages: 3
ASROCK P81 Pro3 Quick Install Manual preview
P81 Pro3
Brand: ASROCK Pages: 145
Abit NF-M2P Installation Manual preview
NF-M2P
Brand: Abit Pages: 32
PC Partner 35-AA33 0 Series Manual preview
35-AA33 0 Series
Brand: PC Partner Pages: 32
PC Chips A33G Series User Manual preview
A33G Series
Brand: PC Chips Pages: 33

Brands by name

Popular brands

Load more brands