Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 813 | Manualshive

Page: 813 / 1426

background image

Serial Management Controllers (SMCs)

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

29-19

Figure 29-10

shows an example of the timing of various events in the SMCE.

Figure 29-10. SMC UART Interrupts Example

29.3.13 SMC UART Controller Programming Example

The following initialization sequence assumes 9,600 baud, 8 data bits, no parity, and 1 stop bit in a 25-MHz
system. BRG1 and SMC1 are used.

1. Configure the port B pins to enable SMTXD1 and SMRXD1. Set PBPAR[24, 25] then clear

PBDIR[24, 25] and PBODR[24, 25].

2. Configure the BRG1. Write BRGC1 with 0x01_0144. The DIV16 bit is not used and the divider is

162 (decimal). The resulting BRG1 clock is 16

×

the preferred bit rate.

3. Connect BRG1 to SMC1 using the SI. Clear SIMODE[SMC1, SMC1CS].

4. Assuming one RxBD at the beginning of dual-port RAM followed by one TxBD, write RBASE

with 0x0000 and TBASE with 0x0008.

5. Write 0x0091 to CPCR to execute the

INIT

RX

AND

TX

PARAMETERS

command.

6. Initialize the SDMA configuration register (SDCR) to 0x0001.

7. Write RFCR and TFCR with 0x10 for normal operation.

8. Write MRBLR with the maximum number of bytes per receive buffer. Assume 16 bytes, so

MRBLR = 0x0010.

9. Write MAX_IDL with 0x0000 in the SMC UART-specific parameter RAM to disable the

MAX_IDL functionality for this example.

10. Clear BRKLN and BRKEC in the SMC UART-specific parameter RAM.

RX

RX

BRK

BRKE

Break

Line Idle

10 Characters

RXD

Characters

Received by SMC UART

Time

Line Idle

TXD

Characters

Transmitted by SMC UART

TX

Line Idle

Line Idle

7 Characters

NOTES:

SMC UART SMCE

Events

1. The first RX event assumes receive buffers are 6 bytes each.
2. The second RX event position is programmable based on the MAX_IDL value.
3. The BRK event occurs after the first break character is received.

SMC UART SMCE

Events

NOTES:

The TX event assumes all seven characters were put into a single buffer, and the TX event occurred when
character was written to the SMC transmit FIFO.

1.

«
...
811
812
813
814
815
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Raptor Pages: 59

Brand: ASROCK Pages: 198

Brand: Gigabyte Pages: 100

Brand: ASROCK Pages: 160

VECTOR 1 MOTHERBOARD

Brand: Vector Graphic Pages: 14

Brand: Hanasis Pages: 31

Z68A-G45 B3 Series

Brand: MSI Pages: 138

Brand: Avalue Technology Pages: 79

Brand: ASROCK Pages: 244

Brand: Gigabyte Pages: 104

Brand: Micronics Pages: 80

Brand: Ebyte Pages: 9

Brand: Torqeedo Pages: 92

Brand: JMD Pages: 23

Brand: ASROCK Pages: 173

Brand: ASROCK Pages: 216

ZigBee RC2200DD

Brand: Radiocrafts Pages: 4

Brand: Axiom Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands