Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 245 | Manualshive

Page: 245 / 1426

background image

Memory Management Unit

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

8-3

memory is updated indirectly, such as when a modified data in the cache is cast-out by newer data at a
different address that maps to the same cache block). The default is configured by MD_CTR[WTDEF].

Also, when translation is disabled (real mode), the entire memory space is treated as guarded by default.
The implications of this are:

1. Speculative load/store accesses are stalled until they are no longer speculative.

2. Speculative instruction fetches outside of the current real-mode page are stalled until they are no

longer speculative. The size of real-mode page is determined by MI_CTR[PPM]. If
MI_CTR[PPM] = 0, the real-mode page size is 4 Kbytes; if MI_CTR[PPM] = 1, the real-mode
page size is 1 Kbyte.

This behavior can result in significant performance degradation.

8.3.2

Translation Enabled

Translations are generated on a per-page basis and are stored in tables in memory. Along with the
translation, each table entry holds attributes for that page, for example, whether a location is cacheable.

Recently used translations are kept in translation lookaside buffers (TLBs) in hardware. In the MPC885,
software handles the table lookup and TLB reload with little hardware assistance. This offers a flexible
translation table structure choice, because many systems would not benefit from a full-featured hardware
translation mechanism.

A TLB hit in multiple entries is avoided when a TLB is being reloaded. When TLB logic detects that a
new effective page number (EPN) overlaps one in the TLB (when taking into account pages sizes, subpage
validity flags, user/supervisor state, address pace ID (ASID), and the SH values of the TLB entries), the
new EPN is written and the old one is invalidated.

The MMU supports a multiple virtual address space model. Each translation is associated with an ASID,
which must equal the address space ID (CASID) for a translation to be valid.

«
...
243
244
245
246
247
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: QDI Pages: 69

Brand: ECS Pages: 27

Brand: PC Partner Pages: 20

Brand: IBASE Technology Pages: 65

Brand: Qiyangtech Pages: 16

Brand: Supermicro Pages: 93

Brand: Texas Instruments Pages: 13

Brand: JETWAY Pages: 54

Brand: unicore Pages: 11

Brand: ASROCK Pages: 153

Brand: DFI Pages: 102

Brand: DFI Pages: 98

bq51010BEVM-764

Brand: Texas Instruments Pages: 26

SMART SPMXCA200

Brand: Spektrum Pages: 16

Brand: Asus Pages: 57

Brand: Asus Pages: 54

Brand: Asus Pages: 57

P8H61-M LX PLUS R2.0

Brand: Asus Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands