Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 157 | Manualshive

Page: 157 / 1426

background image

The MPC8xx Core

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

3-17

Table 3-5

summarizes MPC885 features with respect to the OEA definition.

Table 3-5. OEA-Level Features

Functionality

Description

Machine state
register

The floating-point exception mode (bits FE0 and FE1) is ignored by the MPC885. The IP bit initial
state after reset is set as programmed by the reset configuration specified in

Section 6.1.2.1,

“System Reset Interrupt (0x00100).”

Processor
version register

The value of the PVR register’s version field is 0x0050. The value of the revision field is 0x0000, and
it is incremented each time the device is revised, to allow software to distinguish between revisions.

Other OEA
registers

The following registers are not implemented: SDR1, BAT registers, segment registers, and EAR

Page size

The MPC885 differs from the OEA-defined memory management mode with respect to page sizes.
Page sizes are 4, 16, and 512 Kbytes, and 8 Mbytes with an optional subpage granularity of 1 Kbyte
for 4-Kbyte pages in a maximum physical memory size of 4 Gbytes. Neither ordinary nor direct-store
segments are supported.

Address space

The MPC885 differs from the OEA-defined memory management model. Specifically, it does not
support the same address translation mechanism that requires an intermediate 52-bit virtual
address. It also does not support block address translation or the associated block address
translation SPRs. In its place, the MPC885’s internal memory space includes memory-mapped
control registers and memory used by various modules on the chip. This memory is part of the main
memory as seen by the core but cannot be accessed by any external system device.

Address
translation

If address translation is disabled (MSR[IR] = 0 for instruction accesses or MSR[DR] = 0 for data
accesses), the EA is treated as the physical address and is passed directly to the memory
subsystem. Otherwise, the EA is translated by using the MMU’s TLB mechanism. Instructions are
not fetched from no-execute or guarded memory and data accesses are not executed speculatively
to or from the guarded memory. The features of the MMU hardware are as follows:
• 32-entry fully-associative ITLB
• 32-entry fully-associative DTLB
• Supports up to 16 virtual address spaces
• Supports 16 access protection groups
• Supports fast software table search mechanism
The MPC885 MMU is described in detail in

Chapter 8, “Memory Management Unit.”

Reference and
change bits

No reference bit is supported by the MPC885. However, the change bit is supported by using the
data TLB error exception mechanism when writing to an unmodified page.

Memory
protection

Two protection modes are supported by the MPC885:
• Domain manager mode
• PowerPC mode
See

Chapter 8, “Memory Management Unit.”

«
...
155
156
157
158
159
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

ASC Bridge Board

Brand: Lattice Semiconductor Pages: 25

ATmega328P Xplained Mini

Brand: Microchip Technology Pages: 26

Brand: IEI Technology Pages: 147

Brand: MSI Pages: 36

Brand: Gigabyte Pages: 87

7001G - VIA Mini ITX Motherboard

Brand: VIA Technologies Pages: 76

Brand: Yamaha Pages: 114

Brand: Microchip Technology Pages: 44

Brand: WynMax Pages: 68

Brand: ASROCK Pages: 64

A320M PRO-VH PLUS

Brand: MSI Pages: 154

Brand: C&T Solution Pages: 48

Brand: MSI Pages: 164

TLV320AIC12KEVM-K

Brand: Texas Instruments Pages: 40

Brand: ST Pages: 52

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands