Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 824 | Manualshive

Page: 824 / 1426

background image

Serial Management Controllers (SMCs)

MPC885 PowerQUICC Family Reference Manual, Rev. 2

29-30

Freescale Semiconductor

4. Write RBASE and TBASE in the SMC parameter RAM to point to the RxBD and TxBD in the

dual-port RAM. Assuming one RxBD at the beginning of the dual-port RAM followed by one
TxBD, write RBASE with 0x0000 and TBASE with 0x0008.

5. Program CPCR to execute the

INIT

RX

AND

TX

PARAMETERS

command. Write 0x0091 to CPCR.

6. Write 0x0001 to the SDCR to initialize the SDCR.

7. Write RFCR and TFCR with 0x10 for normal operation.

8. Write MRBLR with the maximum bytes per receive buffer. Assuming 16 bytes, MRBLR =

0x0010.

9. Initialize the RxBD assuming the buffer is at 0x0000_1000 in main memory. Write 0xB000 to

RxBD[Status and Control], 0x0000 to RxBD[Data Length] (optional), and 0x0000_1000 to
RxBD[Buffer Pointer].

10. Initialize the TxBD assuming the Tx buffer is at 0x0000_2000 in main memory and contains five

8-bit characters. Write 0xB000 to TxBD[Status and Control], 0x0005 to TxBD[Data Length], and
0x0000_2000 to TxBD[Buffer Pointer].

11. Write 0xFF to SMCE to clear any previous events.

12. Write 0x13 to SMCM to enable all possible SMC interrupts.

13. Write 0x0000_0010 to the CIMR to allow SMC1 to generate a system interrupt. The CICR should

also be initialized.

14. Write 0x3830 to the SMCMR to configure 8-bit characters, unreversed data, and normal operation

(not loopback). The transmitter and receiver are not enabled yet.

15. Write 0x3833 to the SMCMR to enable the SMC transmitter and receiver. This additional write

ensures that TEN and REN are enabled last.

After 5 bytes are sent, the TxBD is closed; after 16 bytes are received the receive buffer is closed. Any data
received after 16 bytes causes a busy (out-of-buffers) condition since only one RxBD is prepared.

29.4.13 SMC Transparent TSA Programming Example

The following is an example initialization sequence for the SMC1 transparent channel over the TSA. It is
assumed that the TSA and the TDM pins have been set up to route time-slot data to the SMC transmitter
and receiver.

Chapter 20, “Serial Interface,”

has examples for configuring the TSA which provides

transmit and receive clocks and synchronization signals internally.

1. Write RBASE and TBASE in the SMC parameter RAM to point to the RxBD and TxBD in the

dual-port RAM. Assuming one RxBD at the beginning of the dual-port RAM followed by one
TxBD, write RBASE with 0x0000 and TBASE with 0x0008.

2. Program CPCR to execute the

INIT

TX

AND

RX

PARAMETERS

command. Write 0x0091 to CPCR.

3. Initialize the SDCR to 0x0001.

4. Write RFCR and TFCR with 0x10 for normal operation.

5. Write MRBLR with the maximum number of bytes per receive buffer. Assume 16 bytes, so

MRBLR = 0x0010.

«
...
822
823
824
825
826
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Yamaha Pages: 20

Brand: Analog Devices Pages: 8

Brand: IEI Technology Pages: 17

Brand: JETWAY Pages: 44

Brand: Biostar Pages: 65

Brand: Biostar Pages: 56

Brand: MINN KOTA Pages: 16

Brand: ASROCK Pages: 212

Brand: Commell Pages: 60

Brand: Silicon Laboratories Pages: 9

Brand: Advantech Pages: 88

Brand: Supermicro Pages: 97

Brand: MiTAC Pages: 91

Brand: ECS Pages: 70

Brand: Dynatem Pages: 57

Brand: Intel Pages: 36

LMQ61460EVM-400K

Brand: Texas Instruments Pages: 20

LanParty PRO875B

Brand: DFI Pages: 141

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands