Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 945 | Manualshive

Page: 945 / 1426

background image

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

35-1

Chapter 35
CPM Interrupt Controller

The CPM interrupt controller (CPIC) accepts and prioritizes the internal and external interrupt requests
from the CPM blocks and passes them to the system interface unit (SIU). The CPIC also provides a vector
during the core interrupt acknowledge cycle.

35.1

Features

The following is a list of the CPIC’s main features:

•

Twenty-nine interrupt sources—17 internal and 12 external (through port C)

•

Sources can be assigned to a programmable interrupt level.

•

Programmable priority between USB and SCCs

•

Two priority schemes for the USB and SCCs

•

Programmable highest priority request

•

Fully nested interrupt environment

•

Individual interrupt sources can be masked in the CPM interrupt mask register (CIMR).

•

Unique vector number for each interrupt source

The CPIC manages interrupts from internal CPM sources. These sources are primarily generated by
controllers, such as the USB, SCCs, SMCs, SPI, and I

2

C but also include the 12 general-purpose timers

and port C parallel I/O signals described in

Section 34.4, “Port C.”

More than one of these sources may

generate interrupts at the same time; therefore, the CIMR register is provided for masking individual
sources. Additional masking is provided for specific interrupt events within each controller that reports
interrupts through the CPIC. These mask registers are described in the chapters that describe individual
controllers. All CPIC-managed interrupt sources are prioritized and bits are set in the CPM interrupt
pending register (CIPR).

Figure 35-1

shows the MPC885 interrupt structure. The left of the figure shows individual interrupt

sources managed by the CPIC, which signals CPIC-managed interrupts to the SIU, shown in the middle
of

Figure 35-1

. All interrupts signaled by the CPIC are presented to the SIU at a single programmable

priority level (0–7). In turn, the SIU controls which PowerPC architecture-defined external interrupt
exception condition is reported to the MPC8xx core.

For information about the SIU interrupt structure, see

Section 10.5.1, “Interrupt Structure.”

For

information about the external interrupt exception, see

Section 6.1.2.5, “External Interrupt Exception

(0x00500).”

«
...
943
944
945
946
947
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: A-Trend Pages: 40

FMC XM101 LVDS QSE

Brand: Xilinx Pages: 23

Brand: AOpen Pages: 105

Brand: Infineon Pages: 24

AP0100CSSL00SPGAH-GEVB

Brand: ON Semiconductor Pages: 6

Nucleo STM32F302R8

Brand: ST Pages: 18

Brand: Avalue Technology Pages: 75

Brand: Silicon Laboratories Pages: 16

MEG X570S UNIFY-X MAX

Brand: MSI Pages: 204

Brand: BESTEK Pages: 45

Brand: DAQ system Pages: 52

LCD Programmer Module

Brand: Xtralis VESDA Pages: 54

Brand: ECS Pages: 92

Brand: ASROCK Pages: 18

Brand: Bartels Mikrotechnik Pages: 9

Fatal1ty B150 Gaming K4

Brand: ASROCK Pages: 154

Brand: Commell Pages: 29

Brand: SOLTEK Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands