Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 1141 | Manualshive

Page: 1141 / 1426

background image

Fast Ethernet Controller (FEC)

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

45-19

Table 45-15

describes ECNTRL fields.

45.3.2.9

Interrupt Event (I_EVENT)/Interrupt Mask Register (I_MASK)

When an event sets a bit in the interrupt event register (I_EVENT), shown in

Figure 45-13

, an interrupt is

generated if the corresponding interrupt mask register (I_MASK) bit is set. I_EVENT bits are cleared by
writing ones; writing zeros has no effect.

Table 45-16

describes I_EVENT and I_MASK fields. Note that neither the RxBD or TxBD has an I bit to

enable/disable an interrupt on the receive or transmit buffer. As events occur, they are always reported in
I_EVENT, but only those not masked in I_MASK cause an interrupt. From a system resources and
software performance standpoint, it is advisable to minimize the number of interrupts per frame by
masking TXB and RXB in favor of TFINT and RFINT to notify at the end of frame.

Table 45-15. ECNTRL Field Descriptions

Bits

Name

Description

0–28

—

Reserved. These fields may return unpredictable values and should be masked on a read.
Users should always write these fields to zero.

29

FEC_PINMUX

FEC enable. Read/write. The user must set this bit to enable the FEC function in the 885
in conjunction with 885 pin multiplexing control.

30

ETHER_EN

Ethernet enable.
0 A transfer is stopped after a bad CRC is appended to any frame being sent.
1 The FEC is enabled, and reception and transmission are possible.
The BDs for an aborted transmit frame are not updated after ETHER_EN is cleared. When
ETHER_EN is cleared, the DMA, BD, and FIFO control logic are reset including BD and
FIFO pointers. See

Section 45.3.3.2, “User Initialization (before Setting

ECNTRL[ETHER_EN]).”

31

RESET

Ethernet controller reset. When RESET = 1, the equivalent of a hardware or software reset
is performed but it is local to the FEC. ETHER_EN is cleared and all other FEC registers
take their reset values. Also, any transfers are abruptly aborted. Hardware automatically
clears RESET once the hardware reset is complete (approximately 16 clock cycles).

0

1

2

3

4

5

6

7

8

9

10

15

Field HBERR BABR BABT GRA TFINT TXB RFINT RXB

MII

EBERR

—

Reset

0000_0000_0000_0000

R/W

R/W

Addr

0x0E44 (I_EVENT); 0x0E48 (I_MASK) - FEC1
0x1E44 (I_EVENT); 0x1E48 (I_MASK) - FEC2

16

31

Field

—

Reset

0000_0000_0000_0000

R/W

R/W

Addr

0x0E46(I_EVENT); 0x0E4A (I_MASK) - FEC1
0x1E46(I_EVENT); 0x1E4A (I_MASK) - FEC2

Figure 45-13. I_EVENT/I_MASK Registers

«
...
1139
1140
1141
1142
1143
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: u-blox Pages: 2

Brand: Yamaha Pages: 87

Brand: Analog Devices Pages: 8

Brand: DFI Pages: 104

Brand: QDI Pages: 23

Brand: MAX power Pages: 20

Brand: ST Pages: 22

Brand: MSI Pages: 92

AR0832MBSC25SUFAH-GEVB

Brand: ON Semiconductor Pages: 6

Brand: Analog Devices Pages: 17

Brand: Texas Instruments Pages: 11

Brand: MSI Pages: 104

Brand: JETWAY Pages: 47

Brand: Lite-on Tech Pages: 49

Brand: ASROCK Pages: 43

Brand: C&T Solution Pages: 90

Brand: ASROCK Pages: 160

Desktop Board D850EMD2

Brand: Intel Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands