Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 363 | Manualshive

Page: 363 / 1426

background image

External Signals

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

12-33

BADDR30
REG

Hi-Z

D8

Output

Burst Address 30—This output duplicates the value of A30 when
the following is true:
• An internal master in the MPC875 initiates a transaction on the

external bus.

• An asynchronous external master initiates a transaction.
• A synchronous external master initiates a single beat

transaction.

The memory controller uses BADDR30 to increment the address
lines that connect to memory devices when a synchronous
external master or an internal master initiates a burst transfer.
Register—When an internal master initiates an access to a slave
under control of the PCMCIA interface, this signal duplicates the
value of TSIZ0/REG. When an external master initiates an
access, REG is output by the PCMCIA interface (if it must handle
the transfer) to indicate the space in the PCMCIA card being
accessed.

BADDR[28:29
]

Hi-Z

E8, C5

Output

Burst Address—Outputs that duplicate A[28:29] values when one
of the following occurs:
• An internal master in the MPC875 initiates a transaction on the

external bus.

• An asynchronous external master initiates a transaction.
• A synchronous external master initiates a single beat

transaction.

The memory controller uses these signals to increment the
address lines that connect to memory devices when a
synchronous external or internal master starts a burst transfer.

AS

Hi-Z

C7

Input

Address Strobe—Input driven by an external asynchronous
master to indicate a valid address on A[0:31]. The MPC875
memory controller synchronizes AS and controls the memory
device addressed under its control.

PA[15]
USBRXD

Hi-Z

P14

Bidirectional General-Purpose I/O Port A Bit 15—Bit 15 of the general-purpose

I/O port A.
USBRXD —Receive data. Input to the USB receiver from the
differential line receiver.

PA[14]
USBOE

Hi-Z

U16

Bidirectional

(optional:

open-drain)

General-Purpose I/O Port A Bit 14—Bit 14 of the general-purpose
I/O port A.
USBOE—Output enable. Enables the transceiver to send data on
the bus.

PA[11]
RXD4
MII1-TXD0
RMII1-TXDO

Hi-Z

R9

Bidirectional

(optional:

open-drain)

General-Purpose I/O Port A Bit 11—Bit 11 of the general-purpose
I/O port A.
RXD4—Receive data input for SCC4.
MII1-TXD0—Media independent interface 1, transmit data 0.
RMII1-TXD0—Reduced media-independent interface 1, transmit
data 0.

Table 12-2. MPC875/MPC870 Signal Descriptions (continued)

Name

Hard

Reset

Number

Type

Description

«
...
361
362
363
364
365
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Acer Pages: 12

Brand: Sun Microsystems Pages: 74

Brand: Advantech Pages: 3

Brand: Texas Instruments Pages: 16

Brand: J&W Pages: 40

Brand: IEI Technology Pages: 156

Brand: Infineon Pages: 11

Brand: IDT Pages: 18

Brand: JETWAY Pages: 48

z75a-g45 series

Brand: MSI Pages: 88

Brand: DFI Pages: 113

LanParty UT NF590 SLI-M2R/G

Brand: DFI Pages: 162

Brand: TOHATSU Pages: 130

SY-KT333 DRAGON Plus

Brand: SOYO Pages: 112

Super 7 SY-5EMA+

Brand: SOYO Pages: 16

Brand: Micrel Pages: 6

Brand: Micrel Pages: 10

Brand: Micrel Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands