Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 1043 | Manualshive

Page: 1043 / 1426

background image

ATM Controller

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

39-21

NOTE

The address in the AMEND field for PHY0 is used to calculate the top
addresses for each of the four address matching sub-tables. Therefore,
AMEND should point to the PHY0 channel entry corresponding to the top
of the PHY sub-table with the highest number of channel entries.

39.6.1.2

Address Compression Multi-PHY Support

During multi-PHY operations additional 2 to 5 PHY address bits (depending on the number of PHY
address pins) are appended as the least significant bits of the first-level address pointer. See

Section 39.1.2,

“Address Compression (SRSTATE[EXT,ACP] = 11).”

NOTE

PHYn uses RCTn as its default raw cell queue.

39.6.1.3

CAM Multi-PHY Support

When performing CAM addressing the PHY address is added to the CAMADD address. The user must
configure the CAMADD field with the last 7 address bits cleared. The PHY address is driven on the
ADDR[25–31] signals during the CAM access. This allows the user either to use several separate CAMs
with each mapped to its own group of addresses or to have a single unified CAM with the ADDR[25–31]
signals used as part of the match data for the CAM. See

Section 39.1.3, “CAM Address Mapping

(SRSTATE[EXT,ACP] = 10).”

NOTE

PHYn uses RCTn as its default raw cell queue.

39.6.2

Programming Slave Operation in a Multi-PHY System

The MPC885 should be programmed as if in single-PHY mode when operating as a slave in a multi-PHY
environment. That is, if UTMODE[RSL] and/or UTMODE[TSL] are set, the corresponding parameter
RAM, address mapping mechanism, RCTs, TCTs, APC, etc. should be programmed for single PHY
operation. For example, EAPCSTn[MPY] should be cleared.

The only multi-PHY parameters that do require programming are UTMODE[MPHY] (representing the
MPC885’s UTOPIA slave address) and UTMODE[ADDPIN].

39.7

ATM Commands

The host application issues commands to the ATM controller by writing to the CP command register
(CPCR). The ATM commands are similar to the CP commands provided for other protocols (see

Section 18.6.3, “CP Command Register (CPCR)”

). A unique CP opcode is assigned for all ATM

commands, and a separate ATM opcode selects the specific ATM command. The CPCR format for ATM
commands is shown in

Figure 39-14

.

Note that the worst case ATM command execution latency is 480 clocks, and the typical command
execution latency is 40 clocks for serial ATM and 180 clocks for UTOPIA.

«
...
1041
1042
1043
1044
1045
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

CYTVII-B-E-1M-SK

Brand: Cypress Pages: 19

Brand: Biostar Pages: 51

Brand: IBASE Technology Pages: 56

SERVER SYSTEM SR2500AL

Brand: Intel Pages: 210

Brand: MSI Pages: 112

K8N Neo3 MS-7135

Brand: MSI Pages: 124

SX1211-11SKA868

Brand: Semtech Pages: 30

Brand: Kontron Pages: 105

Side-Power SX100/185T

Brand: SLEIPNER MOTOR AS Pages: 16

E-TEC 40RL 2008

Brand: Evinrude Pages: 58

Brand: JETWAY Pages: 55

Brand: COX Pages: 60

Brand: MSI Pages: 75

Brand: Lapis Pages: 29

Brand: Texas Instruments Pages: 11

Brand: Golden Motor Pages: 22

Brand: J&W Pages: 39

Brand: DFI Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands