manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Reference Manual

The Freescale Semiconductor PowerQUICC MPC870 is a powerful and versatile processing unit designed for high-performance embedded applications. With its comprehensive Reference Manual available for free download, users can easily access in-depth information and instructions on maximizing the product's capabilities. Visit manualshive.com to obtain your free manual today.

Share
Download
background image

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

Glossary-5

 

L

Latency. The time an operation requires. For example, execution latency is the number of 

processor clocks an instruction takes to execute. Memory latency is the number of 
bus clocks needed to perform a memory operation. 

Least-significant bit (lsb). The bit of least value in an address, register, data element, or 

instruction encoding. 

Least-significant byte (LSB). The byte of least value in an address, register, data element, 

or instruction encoding.

Little-endian. A byte-ordering method in memory where the address n of a word 

corresponds to the least-significant byte. In an addressed memory word, the bytes 
are ordered (left to right) 3, 2, 1, 0, with 3 being the most-significant byte. See 
Big-endian.

M

Master, The name given to a bus device that has been granted control, or mastership, of the 

bus. 

Memory access ordering. The specific order in which the processor performs load and store 

memory accesses and the order in which those accesses complete.

Memory controller. A unit whose primary function is to control the external bus memories 

and I/O devices. 

Memory coherency. An aspect of caching in which it is ensured that an accurate view of 

memory is provided to all devices that share system memory.

Memory consistency. Refers to agreement of levels of memory with respect to a single 

processor and system memory (for example, on-chip cache, secondary cache, and 
system memory).

Memory management unit (MMU). The functional unit that is capable of translating an 

effective (logical) address to a physical address, providing protection 
mechanisms, and defining caching methods.

Microarchitecture. The hardware details of a microprocessor’s design. 

Mnemonic. The abbreviated name of an instruction used for coding. 

Modified state. When a cache block is in the modified state, it has been modified by the 

processor since it was copied from memory. See MESI.

Munging. A modification performed on an effective address that allows it to appear to the 

processor that individual aligned scalars are stored as little-endian values, when 
in fact it is stored in big-endian order, but at different byte addresses within double 
words. Note that munging affects only the effective address and not the byte order.

Most-significant bit (msb). The highest-order bit in an address, registers, data element, or 

instruction encoding. 

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Gigabyte GP-WB8260MD Installation Manual preview
GP-WB8260MD
Brand: Gigabyte Pages: 8
LITETRONICS SCR053 Operation Instructions preview
SCR053
Brand: LITETRONICS Pages: 2
JETWAY NU792V User Manual preview
NU792V
Brand: JETWAY Pages: 45
JETWAY M2A480 User Manual preview
M2A480
Brand: JETWAY Pages: 18
Intel NUC5i3MYHE User Manual preview
NUC5i3MYHE
Brand: Intel Pages: 12
JETWAY K8T8AS - REV 3.0 User Manual preview
K8T8AS - REV 3.0
Brand: JETWAY Pages: 26
JETWAY 611CF User Manual preview
611CF
Brand: JETWAY Pages: 57
Newport XPS-DRVP1 User Manual preview
XPS-DRVP1
Brand: Newport Pages: 30
Digilent Cora Z7 Reference Manual preview
Cora Z7
Brand: Digilent Pages: 23
DFI CA100-D User Manual preview
CA100-D
Brand: DFI Pages: 115
TOHATSU MES 4C Owner'S Manual preview
MES 4C
Brand: TOHATSU Pages: 52
Gigabyte GA-H170M-HD3 DDR3 User Manual preview
GA-H170M-HD3 DDR3
Brand: Gigabyte Pages: 44
Gigabyte GA-8N-SLI Pro User Manual preview
GA-8N-SLI Pro
Brand: Gigabyte Pages: 96
NXP Semiconductors Lite5200B User Manual preview
Lite5200B
Brand: NXP Semiconductors Pages: 138
Fujitsu D2779 Technical Manual preview
D2779
Brand: Fujitsu Pages: 32
Fujitsu D2811 Short Description preview
D2811
Brand: Fujitsu Pages: 23
Fujitsu D2619-N Technical Manual preview
D2619-N
Brand: Fujitsu Pages: 40
Fujitsu D2671 Technical Manual preview
D2671
Brand: Fujitsu Pages: 41

Brands by name

Popular brands

Load more brands