Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 931 | Manualshive

Page: 931 / 1426

background image

Parallel I/O Ports

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

34-13

5. Write the signal value using the PCDAT register.

The following steps can be taken to configure a port C signal as a general-purpose input signal that does
not generate an interrupt:

1. Write the corresponding PCPAR bit with a zero.

2. Write the corresponding PCDIR bit with a zero.

3. Write the corresponding PCSO bit with a zero.

4. The corresponding PCINT bit is a ‘don’t care’ bit.

5. Write the corresponding CIMR bit with a zero to prevent interrupts from being generated to the

core.

6. Read the signal value using the PCDAT register.

When a port C signal is configured as a general-purpose I/O input, a change in the port C interrupt register
(PCINT) causes an interrupt request signal to be sent to the CPIC. Each port C signal can be configured to
assert an interrupt request either when a high-to-low change occurs or when any change occurs. Each port
C signal asserts a unique interrupt request to the CPM interrupt pending register (CIPM) (see

Section 35.5.2, “CPM Interrupt Pending Register (CIPR)”

) and has a different internal interrupt priority

level within the CPM interrupt controller (see

Section 35.2, “CPM Interrupt Source Priorities”

).

Requests can be masked independently in the CPM interrupt mask register (CPMR). See

Section 35.5.3,

“CPM Interrupt Mask Register.”

The following steps configure a port C signal as a general-purpose input

that generates an interrupt:

1. Write the corresponding PCPAR bit with a 0.

2. Write the corresponding PCDIR bit with a 0.

3. Write the corresponding PCSO bit with a 0.

4. Set the PCINT bit to determine which edges cause interrupts.

5. Write the corresponding CIMR bit with a 1 so that interrupts can be sent to the core.

6. Read the signal value using the PCDAT register.

The port C signals associated with CDx and CTSx have a mode of operation in which the signal can be
connected to the SCC internally but can also generate interrupts. Port C still detects changes on CTS and
CD and asserts the corresponding interrupt request, but the SCC simultaneously uses CTS and/or CD to
control operation automatically. This allows the implementation of V.24, X.21, and X.21 bis protocols with
help from other general-purpose I/O signals. To configure a port C signal as a CTS or CD signal that
connects to the SCC and generates interrupts, follow these steps:

1. Write the corresponding PCPAR bit with a 0.

2. Write the corresponding PCDIR bit with a 0.

3. Write the corresponding PCSO bit with a 1.

4. Set the PCINT bit to determine which edges cause interrupts.

5. Write the corresponding CIMR bit with a 1 so that interrupts can be sent to the core.

6. The signal value can be read at any time using the PCDAT register.

«
...
929
930
931
932
933
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Microchip Technology Pages: 17

Brand: NXP Semiconductors Pages: 28

Brand: NXP Semiconductors Pages: 16

Brand: QDI Pages: 20

Fatal1ty Z87 Killer Series

Brand: ASROCK Pages: 102

Brand: Linear Technology Pages: 7

Brand: Supero Pages: 101

Brand: JETWAY Pages: 47

Brand: Atiosys Pages: 1

Brand: Texas Instruments Pages: 24

Spacewalker AV40

Brand: Shuttle Pages: 81

Brand: Texas Instruments Pages: 14

Brand: Gigabyte Pages: 116

Brand: Aaeon Pages: 74

Brand: Curtis Instruments Pages: 46

Brand: Avalue Technology Pages: 83

Brand: Award Pages: 60

Brand: ASROCK Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands