Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 726 | Manualshive

Page: 726 / 1426

background image

SCC Asynchronous HDLC Mode and IrDA

MPC885 PowerQUICC Family Reference Manual, Rev. 2

25-4

Freescale Semiconductor

25.6

Exceptions to RFC 1549

•

An unmapped control character that follows 0x7D is modified by the XOR process. The CRC
check should catch this.

•

In addition to the abort

sequence, frames are terminated by the following errors:

— CD (carrier detect) lost

— Receiver overrun

— Framing error

— Break sequence

•

If an invalid sequence(0x7D7D) is received, the first control escape character is discarded, and the
second is unconditionally XORed with 0x20. The sequence is thus stored in the buffer as 0x5D.

25.7

Asynchronous HDLC Channel Implementation

The following points are specific to asynchronous HDLC channel implementation:

•

Flag sequence—The transmitter automatically generates the opening and closing flags. The
receiver removes opening and closing flags before writing a frame to memory and receives frames
with only one shared flag between frames, ignoring multiple flags.

•

Address field—The address field is neither generated nor examined by the microcode while
sending or receiving. The destination address field of the frame must be included in the Tx buffer.
Any address field compression, expansion, or checking must be performed by the core.

•

Control field—The control field is neither generated nor examined by the microcode during a
transfer. The control field of the frame must be included in the buffer. Any control field
compression, expansion, or checking is done by the core.

•

Frame check sequence—When sending, the frame check sequence (FCS) is appended to the frame
before the closing flag is sent. The FCS is generated on the original frame before transparency
characters, start/stop bits, or flags are added. When receiving, the FCS is checked automatically
and calculated after any transparency characters, start/stop bits, and flags are removed. For both,
the controller uses only a 16-bit CRC-CCITT polynomial.

•

Encoding—The asynchronous HDLC controller supports 8 data bits, one start bit, one stop bit, and
no parity. Program PSMR[CHLN] to 0b11 for proper operation.

•

Idle characters—When sending, the asynchronous HDLC controller sends idle characters when no
data is available; when receiving, it ignores idle characters.

«
...
724
725
726
727
728
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: M5Stack Pages: 16

Brand: CIRCUIT DESIGN Pages: 9

Brand: JETWAY Pages: 48

Brand: IBASE Technology Pages: 65

Brand: Gigabyte Pages: 31

Brand: DFI Pages: 46

Brand: Supero Pages: 92

Brand: BOSER Technology Pages: 38

Brand: Zeal-All Pages: 9

Brand: Infineon Pages: 30

MPG Z390 GAMING PLUS

Brand: MSI Pages: 76

Brand: Microchip Technology Pages: 18

Brand: Watersnake Pages: 24

Brand: ASROCK Pages: 57

Brand: DFI Pages: 83

Infinity NF650I Ultra

Brand: DFI Pages: 155

MBD-X11SDV-12C-TP8F

Brand: Supermicro Pages: 123

Brand: DFI Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands