Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 1011 | Manualshive

Page: 1011 / 1426

background image

ATM Parameter RAM

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

38-7

Table 38-3

describes additional parameters needed to configure the SCCs for serial ATM operation.

0x9C

STATBASE

Hword

Statistics table base pointer. Contains the 32-byte-aligned base
address in the dual-port RAM of the statistics table. STATBASE is an
offset from the beginning of dual-port RAM. See

Section 39.5,

“Statistical Counters.”

In UTOPIA mode, STATBASE is valid only when UTMODE[STAT] is
set; see

Section 43.2, “UTOPIA Mode Register (UTMODE).”

In serial mode, clearing STATBASE disables the gathering of
statistics; otherwise, STATBASE is assumed to be a valid base
pointer.

0x9E

—

Hword

Reserved

0xA6

APCTIMERREF

Hword

Current timer reference value for APC flux compensation. The user
should initialize this field to 0. Used for APC flux compensation only.

0xA8

APCTIMERADDR

Word

This field must contain the absolute memory address of register
TCN4, i.e., the upper 16 bit must match the respective IMMR content
and the lower 16 bits must be set to 0x09ae, which references TCN4.
Used for APC flux compensation only.

0xAC–0xBF

—

Reserved

Table 38-3. Serial ATM Parameter RAM Map

Offset

from SCC

Base

Name

Width

Description

0xC0

ALPHA

Hword

Receiver delineation alpha/delta counters. The ATM controller applies the
HEC delineation mechanism described in ITU specification I.432 where
ALPHA and DELTA are initialized by the user to a value from 0 to 63. (The
ITU specification I.432 recommendation is 0x7 for alpha and 0x6 for delta.)
The receiver updates ALPHA and DELTA; the user should not write to
these locations during receive operations.

0xC2

DELTA

Hword

0xC4

RSTUFF

1

Word

Receive data stuffing location (for 53 to 52 byte conversion).

0xC8

SHUFFLESTATE

Hword

Receiver data shuffling internal state.
Should be cleared during initialization.

0xCA

RHECTEMP

1

Hword

Receiver temporary HEC storage area

0xCC

THECTEMP

1

Hword

Transmitter temporary HEC storage area

0xCE

ASTATUS

Hword

Cell synchronization status register. See

Section 38.8, “Serial Cell

Synchronization Status Register (ASTATUS).”

Should be cleared during

initialization.

0xD0

HEC_ERR

Hword

HEC error counter. Contains a 16-bit counter for incoming cells with HEC
errors. HEC_ERR may be read by the user at any time. Should be cleared
during initialization.

0xD2

—

Hword

Reserved

Table 38-2. ESAR Mode Parameters (continued)

Offset from

SCC Base

Name

Width

Description

«
...
1009
1010
1011
1012
1013
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

SBC81206 Series

Brand: AXIOMTEK Pages: 74

Brand: Yamaha Pages: 76

Brand: hager Pages: 4

Brand: Intel Pages: 78

Brand: ECS Pages: 56

Brand: PC Partner Pages: 20

Brand: Analog Devices Pages: 13

Brand: Micrel Pages: 14

Brand: IBASE Technology Pages: 60

Brand: AMD Geode Pages: 51

Brand: EVGA Pages: 2

Brand: ASROCK Pages: 56

Brand: ZMDI Pages: 25

Outboard Motor BF5A

Brand: Honda Pages: 84

Brand: Intel Pages: 92

Brand: Albatron Pages: 46

Brand: Ublox Pages: 2

Brand: Texas Instruments Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands