Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 636 | Manualshive

Page: 636 / 1426

background image

Serial Interface

MPC885 PowerQUICC Family Reference Manual, Rev. 2

20-30

Freescale Semiconductor

20.2.5.2

Programming the IDL Interface

To program the IDL interface, first program SIMODE[GMx] to the IDL grant mode for that channel. If the
receive and transmit sections interface to the same IDL bus, set SIMODE[CRTx] to internally connect the
Rx clock and sync signals to the transmit section. Then program the SI RAM used for the IDL channels to
the preferred routing. See

Section 20.2.3.8, “SI RAM Programming Example.”

Define the IDL frame structure by programming SIMODE[xFSD] to have a 1-bit delay from frame sync
to data, SIMODE[FE] to sample the sync on the falling edge, and SIMODE[CE] to transmit on the rising
edge of the clock. Program L1TXDx to be three-stated when inactive via the parallel I/O open-drain
register. To support the D channel, set the appropriate SICR[GR] bit and program the RAM entry to route
data to the chosen SCC. The two definitions of IDL, 8- and 10-bit, are only supported by modifying the SI
RAM programming. In both cases, L1GRx is sampled with L1TSYNCx and transferred to the D-channel
SCC as a grant indication. Repeat the same procedure for an IDL bus on the second TDM channel.

For example, based on the same 10-bit format as in

Section 20.2.3.8, “SI RAM Programming Example,”

implement an IDL bus using SCC2, SCC3, and SMC2 connected to the TDM channel as follows:

1. Program both the Rx and Tx sections of the SI RAM as in

Table 20-11

. Write unused entries with

0x0001_0000.

2. SIMODE = 0x8000_0145. Only TDMa is used. SMC2 is connected to the TSA.

3. SICR = 0x00C0_4000. SCC2 and SCC3 are connected to the TSA. SCC3 supports the grant

mechanism since it is on the D channel.

4. PAODR[9] = 1. Configure L1TXDa to be an open-drain output.

5. PAPAR[7–9] = 0b111. Configure L1TXDa, L1RXDa, and L1RCLKa.

6. PADIR[7–9] = 0b011. Configure L1TXDa, L1RXDa, and L1RCLKa.

7. PCPAR[5,4] = 1. Configure L1TSYNCa, and L1RSYNCa.

8. L1TSYNCa performs the L1GRa grant function and is therefore an input but does not need to be

configured by clearing PCDIR. L1RSYNCa is an input but does not need to be configured in
PCDIR.

9. PDPAR[6] Configure L1RQa,

10. PCDIR[6] = 0. L1RQa is an output. SIGMR = 0x04. Enable TDMa (one static TDM).

11. SICMR is not used.

Table 20-11. SI RAM Settings for IDL Interface

Entry

Number

SI RAM

SWTR

SSEL

CSEL

CNT

BYT

LST

Description

1

0

0000

010

0000

1

0

8 bits SCC2 (B1)

2

0

0000

011

0000

0

0

1 bit SCC3 (D)

3

0

0000

000

0000

0

0

1 bit no support

4

0

0000

110

0000

1

0

8 bits SMC2 (B2)

5

0

0001

011

0000

0

1

1 bit SCC3 (D) and strobe1

«
...
634
635
636
637
638
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Intel Pages: 78

870 Extreme3 R2.0

Brand: ASROCK Pages: 17

Brand: ASROCK Pages: 126

Brand: MSI Pages: 76

S1V30080 Series

Brand: Seiko Epson Pages: 10

Brand: JETWAY Pages: 48

Brand: Aaeon Pages: 119

Brand: ASROCK Pages: 64

Brand: Biostar Pages: 31

Brand: ECS Pages: 82

Brand: Oki Pages: 24

Brand: ASROCK Pages: 2

Brand: Mini-Itx Pages: 174

Brand: DFI Pages: 5

Brand: Gigabyte Pages: 100

BOOSTXL-DRV8323Rx

Brand: Texas Instruments Pages: 28

Brand: Texas Instruments Pages: 27

EV MOD CH101-01-02

Brand: TDK Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands