Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 713 | Manualshive

Page: 713 / 1426

background image

SCC HDLC Mode

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

23-17

The HDLC bus differs from the I.430 and T1.605 standards as follows:

•

The HDLC bus uses a separate input signal rather than the echo bit to monitor data; the transmitted
data is simply connected to the CTS input.

•

The HDLC bus is a synchronous, digital open-drain connection for short-distance configurations,
rather than the more complex S/T interface.

•

Any HDLC-based frame protocol can be used at layer 2, not just LAPD.

•

HDLC bus devices wait 8–10 rather than 7–10 bit times before transmitting. (HDLC bus has only
one class.)

The collision-detection mechanism supports only:

•

NRZ-encoded data

•

A common synchronous clock for all receivers and transmitters

•

Non-inverted data (GSMR[RINV, TINV] = 0)

•

Open-drain connection with no external transceivers

Figure 23-10

shows the most common HDLC bus LAN configuration, a multimaster configuration. A

station can transfer data to or from any other LAN station. Transmissions are half-duplex, which is typical
in LANs.

Figure 23-10. Typical HDLC Bus Multimaster Configuration

In single-master configuration, a master station transmits to any slave station without collisions. Slaves
communicate only with the master, but can experience collisions in their access over the bus. In this
configuration, a slave that communicates with another slave must first transmit its data to the master, where
the data is buffered in RAM and then resent to the other slave. The benefit of this configuration, however,
is that full-duplex operation can be obtained. In a point-to-multipoint environment, this is the preferred
configuration.

Figure 23-11

shows the single-master configuration.

HDLC Bus

Controller

RXD

CTS

TXD

A

RCLK/TCLK

HDLC Bus

Controller

RXD

CTS

TXD

B

RCLK/TCLK

HDLC Bus

Controller

RXD

CTS

TXD

C

RCLK/TCLK

Clock

HDLC Bus LAN

+ 5 V

R

Master

Master

Master

Notes:

1. Transceivers may be used to extend the LAN size.
2. The TXD pins of slave devices should be configured to open-drain in the port C parallel I/O port.
3. Clock is a common RCLK/TCLK for all stations.

«
...
711
712
713
714
715
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Ublox Pages: 21

Brand: ASROCK Pages: 95

Brand: Yamaha Pages: 223

Brand: Supermicro Pages: 91

Brand: Texas Instruments Pages: 54

IMBA-BDE-1518-R10

Brand: IEI Technology Pages: 14

Brand: Global American Pages: 37

Brand: Gigabyte Pages: 93

Brand: ITX SECURITY Pages: 18

Brand: Pure Photonics Pages: 11

PROTO1 Xplained Pro

Brand: Atmel Pages: 17

Brand: Socket Pages: 37

R3288LC-2N Series

Brand: JETWAY Pages: 44

Brand: MSI Pages: 6

Brand: AOpen Pages: 125

Brand: GigaDevice Semiconductor Pages: 16

Brand: DFI Pages: 107

Brand: Intel Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands