Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 639 | Manualshive

Page: 639 / 1426

background image

Serial Interface

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

20-33

clock rate. Also, if the receive and transmit sections are used to interface with the same GCI bus, set
SIMODE[CRTx] to internally connect the Rx clock and sync signals to the SI RAM transmit section. Then
define the GCI frame routing and strobe select using the SI RAM.

When the receive and transmit sections use the same clock and sync signals, the sections should use the
same configuration. Also, L1TXDx in the I/O register should be configured as an open-drain output. To
support the monitor and C/I channels in GCI, those channels should be routed to an SMC. To support the
D channel when there is no possibility of collision, clear SICR[GRx] for the SCC that supports the D
channel.

20.2.6.2.2

SCIT Mode

To interface with the GCI/SCIT bus, configure SIMODE for basic GCI/SCIT operation. Then program the
SI RAM to support a 96-bit frame length and the frame sync to be the GCI sync pulse. Generally, the SCIT
bus supports the D channel access collision mechanism. For this purpose, set SIMODE[CRTx] so the
receive and transmit sections use the same clock and sync signals and program SICR[GRx] to transfer the
D channel grant to the supporting SCC. The received bit (grant) should be marked by programming the
CSEL (channel select) bits of the SI RAM to 0b111 for an internal assertion of a strobe. This bit is sampled
by the SI and transferred to the D-channel SCC as the grant. The grant is generally bit 4 of the C/I in
channel 2 of the GCI bus, but any bit slot can be selected in the SI RAM.

20.2.6.3

GCI Interface (SCIT Mode) Programming Example

Assuming SCC2 is connected to the B1 channel, SMC2 to the B2 channel, SCC3 to the D channel, and
SMC1 to the C/I channels, the initialization sequence is as follows:

1. Program both the Rx and Tx sections of the SI RAM as shown in

Table 20-12

. Write all unused

entries with 0x0001_0000. Note that this example is for SCIT mode. For normal mode, delete the
last three entries in

Table 20-12

and set the LST bit in the new last entry.

2. SIMODE = 0x8000_80E0. Only TDMa is used. SMC1 and SMC2 are connected.

Table 20-12. SI RAM Settings for GCI Interface (SCIT Mode)

Entry

Number

SI RAM

SWTR

SSEL

CSEL

CNT

BYT

LST

Description

1

0

0000

010

0000

1

0

8 bits SCC2 (B1)

2

0

0000

110

0000

1

0

8 bits SMC2 (B2)

3

0

0000

101

0000

1

0

8 bits SMC1 (M)

4

0

0000

011

0001

0

0

2 bits SCC3 (D)

5

0

0000

101

0101

0

0

6 bits SMC1 (I + A + E)

6

0

0000

000

0110

1

0

Skip 7 bytes

7

0

0000

000

0001

0

0

Skip 2 bits

8

0

0000

111

0000

0

1

D grant bit

«
...
637
638
639
640
641
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Gigabyte Pages: 46

PowerSoC CY3267

Brand: Cypress Pages: 12

Analog Devices DC2605A

Brand: Linear Pages: 16

Brand: DFI Pages: 60

Brand: JETWAY Pages: 43

Brand: Texas Instruments Pages: 21

Brand: Vox Technologies Pages: 36

Brand: BOSER Technology Pages: 38

Brand: Biostar Pages: 32

Brand: Systium Technologies Pages: 4

Brand: COX Pages: 60

Brand: Ublox Pages: 32

BD93F10MWV-EVK-001

Brand: Rohm Pages: 20

Brand: EPOX Pages: 83

Qseven FS700 Series

Brand: DFI Pages: 18

Brand: DFI Pages: 46

Brand: Motorola Pages: 57

PATX3070 Series

Brand: Motorola Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands