manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Reference Manual

The Freescale Semiconductor PowerQUICC MPC870 is a powerful and versatile processing unit designed for high-performance embedded applications. With its comprehensive Reference Manual available for free download, users can easily access in-depth information and instructions on maximizing the product's capabilities. Visit manualshive.com to obtain your free manual today.

Share
Download
background image

SCC AppleTalk Mode

MPC885 PowerQUICC Family Reference Manual, Rev. 2

24-2

Freescale Semiconductor

 

Frames are sent in groups known as dialogs, which are handled by the software. For instance, to transfer 
a data frame, three frames are sent over the network. An RTS frame (not to be confused with the RS-232 
RTS pin) is sent to request the network, a CTS frame is sent by the destination node, and the data frame is 
sent by the requesting node. These three frames comprise one possible type of dialog. After a dialog 
begins, other nodes cannot start sending until the dialog is complete. Frames within a dialog are sent with 
a maximum interframe gap (IFG) of 200 µs. Although the LocalTalk specification does not state it, there 
is also a minimum recommended IFG of 50 µs. Dialogs must be separated by a minimum interdialog gap 
(IDG) of 400 µs. In general, these gaps are implemented by the software.

Depending on the protocol, collisions should be encountered only during RTS and ENQ frames. Once 
frame transmission begins, it is fully sent, regardless of whether it collides with another frame. ENQ 
frames are infrequent and are sent only when a node powers up and enters the network. A higher-level 
protocol controls the uniqueness and transmission of ENQ frames.

In addition to the frame fields, LocalTalk requires that the frame be FM0 (differential Manchester space) 
encoded, which requires one level transition on every bit boundary. If the value to be encoded is a logical 
zero, FM0 requires a second transition in the middle of the bit time. The purpose of FM0 encoding is to 
avoid having to transmit clocking information on a separate wire. With FM0, the clocking information is 
present whenever valid data is present.

24.2

Features

The following list summarizes the features of the SCC in AppleTalk mode:

•

Superset of the HDLC controller features

•

FM0 encoding/decoding

•

Programmable transmission of sync sequence

•

Automatic postamble transmission

•

Reception of sync sequence does not cause extra SCCE[DCC] interrupts

•

Reception is automatically disabled while sending a frame

•

Transmit-on-demand feature expedites frames

•

Connects directly to an RS-422 transceiver

24.3

Connecting to AppleTalk

As shown in 

Figure 24-2

, the MPC885 connects to LocalTalk, and, using TXD, RTS, and RXD, is an 

interface for the RS-422 transceiver. The RS-422, in turn, is an interface for the LocalTalk connector. 
Although it is not shown, a passive RC circuit is recommended between the transceiver and connector.

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

DFI 852GME-MGF Pro User Manual preview
852GME-MGF Pro
Brand: DFI Pages: 39
Lattice Semiconductor ASC Bridge Board User Manual preview
ASC Bridge Board
Brand: Lattice Semiconductor Pages: 25
Waveshare NRF52840 User Manual preview
NRF52840
Brand: Waveshare Pages: 72
JETWAY M2A480 User Manual preview
M2A480
Brand: JETWAY Pages: 18
DIEBOLD NIXDORF P1.0-APL-AIO User Manual preview
P1.0-APL-AIO
Brand: DIEBOLD NIXDORF Pages: 96
Renesas RTKA788152DE0000BU Manual preview
RTKA788152DE0000BU
Brand: Renesas Pages: 11
Microsemi VSC8584 User Manual preview
VSC8584
Brand: Microsemi Pages: 15
Tews Technologies TVME220 Series User Manual preview
TVME220 Series
Brand: Tews Technologies Pages: 26
BCM BC67Q Quick Start Card preview
BC67Q
Brand: BCM Pages: 5
MSI MS-7758 (v3.x) Manual preview
MS-7758 (v3.x)
Brand: MSI Pages: 92
OLIMEX A20-OLINUXINO-LIME User Manual preview
A20-OLINUXINO-LIME
Brand: OLIMEX Pages: 49
QDI BrillianX 1S/2000 Manual preview
BrillianX 1S/2000
Brand: QDI Pages: 63
Analog Devices AD9361 Reference Manual preview
AD9361
Brand: Analog Devices Pages: 128
ASROCK H55M-LE - - 01-2010 Installation Manual preview
H55M-LE - - 01-2010
Brand: ASROCK Pages: 181
AOpen AX45F-1394 Easy Installation Manual preview
AX45F-1394
Brand: AOpen Pages: 8
TYAN S3022 Manual preview
S3022
Brand: TYAN Pages: 47
SLEIPNER MOTOR AS Side-Power SX100/185T Installation And User Manual preview
Side-Power SX100/185T
Brand: SLEIPNER MOTOR AS Pages: 16
Semtech Lora Mote User Manual preview
Lora Mote
Brand: Semtech Pages: 16

Brands by name

Popular brands

Load more brands