Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 1112 | Manualshive

Page: 1112 / 1426

background image

AAL2 Implementation

MPC885 PowerQUICC Family Reference Manual, Rev. 2

44-22

Freescale Semiconductor

Table 44-6

describes the global AAL2 parameters.

Table 44-6. AAL2 Parameter RAM Memory Map

Offset

Bits

Name

Description

0x00

0

RTE

RISC timers enable. To enable the RISC timers when using the timer
CU mechanism set RTE.
0 - RISC timers are disabled.
1 - RISC timers are enabled.

1–15

—

Reserved, should be cleared.

0x02

—

AAL2_SCRATCH1_BASE

16-bit pointer to a 512-byte scratch area in the DPR used by AAL2
during AAL2 operation. This pointer should be 64-byte aligned
(AAL2_SCRATCH1_BASE[26–31]=00_0000).
Note: This pointer is offset from IMMR (and not from IMMR+0x2000
which is the beginning of the DPR). For example, if
AAL2_SCRATCH1 starts at IMMR+0x2C00, the user should program
0x2C00 in AAL2_SCRATCH1_BASE (not 0x0C00).
Host writes this field and clears the 512 bytes during initialization.
AAL2 does not modify this field.

0x04

—

AAL2_ECT_PTR_BASE

AAL2_ECT_PTR_BASE points to the first entry of
AAL2_ECT_PTR_table. AAL2_ECT_PTR_table should start on a
word boundary (AAL2_ECT_PTR_BASE[30-31]=00).

Host writes this field during initialization; see

Section 44.7.2,

“Mapping the AAL2 Connection Tables in External Memory.”

AAL2

does not modify this field

0x08–

0x0A

—

—

Reserved, should be cleared.

0x0C

AAL2_SCRATCH2_BASE

16-bit pointer to a 256-byte scratch area in the DPR used by AAL2
during AAL2 operation. This pointer should start on a half-word
boundary (AAL2_SCRATCH2_BASE[31]=0).
Note: This pointer is offset from IMMR (and not from IMMR+0x2000
which is the beginning of the DPR). For example, if
AAL2_SCRATCH2 starts at IMMR+0x3800, the user should program
0x3800 in AAL2_SCRATCH2_BASE (not 0x1800).
Host writes this field and clears the 256 bytes during initialization.
AAL2 does not modify this field.

0x0E

0–15

—

Reserved, should be cleared.

0x10

—

AAL2_TxWait_BASE

Points to the first row of the AAL2_TxWait_table in the DPR.
This pointer should be on a word boundary
(AAL2_TxWait_BASE[30-31]=00).
Note: This pointer is offset from IMMR (and not from IMMR+0x2000
which is the beginning of the DPR). For example, if the wait table
starts at IMMR+0x2930, the user should program 0x2930 in
AAL2_TxWait_BASE (not 0x0930).
Host writes this field during initialization. AAL2 does not modify this
field

«
...
1110
1111
1112
1113
1114
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Danbit Pages: 70

Brand: AKM Pages: 34

Brand: MSI Pages: 48

Brand: Gigabyte Pages: 96

Brand: Intersil Pages: 26

HBJC390F841VAG34B

Brand: JETWAY Pages: 44

Brand: Ublox Pages: 22

LPC1768-Xplorer

Brand: NGX Technologies Pages: 25

Brand: IEI Technology Pages: 11

Brand: MAX power Pages: 20

Brand: Gigabyte Pages: 96

Brand: One Control Pages: 8

Brand: MSI Pages: 106

Thunder HEsl S2567

Brand: TYAN Pages: 60

Brand: Fujitsu Pages: 30

Brand: DFI Pages: 92

Brand: ASROCK Pages: 260

Brand: Torqeedo Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands