Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 637 | Manualshive

Page: 637 / 1426

background image

Serial Interface

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

20-31

12. SISTR and SIRP do not need to be read, but can be used for debugging once the channels are

enabled.

13. Enable SCC3 for HDLC operation (to handle the LAPD protocol of the D channel), and configure

SCC2 and SMC2 as needed.

20.2.6

GCI Bus Implementation

The MPC885 fully supports both the normal mode (also known as ISDN-oriented modular rev 2.2
(IOM-2)) and the SCIT mode of the general circuit interface (GCI). It also supports the D channel access
control in S/T interface terminals by using the command/indication (C/I) channel.

The GCI bus consists of four signals—two data lines, a clock, and a frame synchronization line. Usually,
an 8-KHz frame structure defines the various channels within the 256 Kbps data rate. The MPC885
supports two independent GCI buses, each with independent receive and transmit sections. With a data rate
of 2,048 Kbps, the interface can also be used in a multiplexed frame structure on which up to eight physical
layer devices multiplex their GCI channels.

In the GCI bus, the clock rate is twice the data rate. The SI divides the input clock by two to produce the
data clock. The MPC885 also has data strobe lines and the 1

×

data rate clock L1CLKOx outputs used as

an interface for devices that do not support the GCI bus. Shown in

Figure 20-27

, the GCI signals for each

Tx and Rx channel are as follows:

•

L1RSYNCx—Used as a GCI sync signal. Input to the MPC885. The clock periods following the
sync pulse designate the GCI frame.

•

L1RCLKx—Used as a GCI clock. Input to the MPC885. The L1RCLKx signal is twice the data
clock.

•

L1RXDx—Used as a GCI receive data. Input to the MPC885.

•

L1TXDx—Used as a GCI transmit data. Open-drain output. Driven only for the bits that are
programmed in the SI RAM. Otherwise, it is three-stated.

•

L1CLKOx—Optional signal; Output. For clock devices that do not interface directly to the GCI. It
is 1

×

output of L1RCLKx.; otherwise, if the double-speed clock is used (SIMODE[DSCx] is set),

it is L1RCLKx divided by 2.

Figure 20-27. GCI Bus Signals

L1CLK

L1SYNC

L1RXD

L1TXD

B1

B2

B1

B2

M (Monitor)

D1 D2

C/I

A E

M (Monitor)

D1 D2

C/I

A E

(2X the Data Rate)

Notes: Clock is not to scale.
L1CLKO is not shown.

«
...
635
636
637
638
639
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

TPS61090EVM-029

Brand: Texas Instruments Pages: 19

Brand: MATSONIC Pages: 78

Brand: MSI Pages: 91

Brand: JETWAY Pages: 43

B550 AORUS ELITE AX V2

Brand: Gigabyte Pages: 12

Brand: Telaire Pages: 4

Brand: R&S Pages: 44

GA-AX370M-Gaming 3

Brand: Gigabyte Pages: 40

Brand: Yamaha Pages: 223

Brand: Gigabyte Pages: 40

Brand: Biostar Pages: 56

Brand: Qiyangtech Pages: 16

Brand: TRU Components Pages: 4

SK-96650_6A0_380-120PMC

Brand: Fujitsu Pages: 39

Brand: Fujitsu Pages: 24

Brand: Fujitsu Pages: 24

SK-91464A-100PMC

Brand: Fujitsu Pages: 28

SK-AMAPOLLO-BASE-V11

Brand: Fujitsu Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands