Freescale Semiconductor PowerQUICC MPC870 Reference Manual Download Page 1166 | Manualshive

Page: 1166 / 1426

background image

SEC Lite Overview

MPC885 PowerQUICC Family Reference Manual, Rev. 2

46-2

Freescale Semiconductor

46.3

SEC Lite Architecture

The SEC Lite was designed to integrate easily into Freescale integrated communications processors. The
ability of the SEC Lite to be a master on the internal bus allows the SEC Lite to off load the data movement
bottleneck normally associated with slave-only cores.

The host processor accesses the SEC Lite through its device drivers using system memory for data storage.
The SEC Lite resides in the peripheral memory map of the processor, therefore when an application
requires cryptographic functions, it simply creates descriptors for the SEC Lite which define the
cryptographic function to be performed and the location of the data. The SEC Lite’s bus-mastering
capability permits the host processor to set up a crypto-channel with a few short register writes, leaving
the SEC Lite to perform reads and writes on system memory to complete the required task.

Figure 46-1. SEC Lite Connected to the MPC885 Internal Bus

46.4

Architectural Overview

A block diagram of the SEC Lite internal architecture is shown in

Figure 46-2

. The bus interface module

is designed to transfer 32-bit words between the bus and any register inside the SEC Lite.

An operation begins with a write of a pointer to the crypto-channel fetch register which points to a data
packet descriptor. The channel requests the descriptor and decodes the operation to be performed. Then
the channel requests the controller to assign crypto execution units and fetch the keys, IV’s and data needed
to perform the given operation. The controller satisfies the requests by assigning execution units to the
channel and by making requests to the master interface. As data is processed, it is written to the individual
execution units output buffer and then back to system memory via the master/slave interface module.

Motorola

PowerPC

Core

System

Interface

Unit

Communications

Processor Module

SEC Lite

8xx Bus

Motorola

PowerPC

Core

System

Interface

Unit

Communications

Processor Module

SEC Lite

8xx Bus

«
...
1164
1165
1166
1167
1168
...
»

Summary of Contents for PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerQUICC MPC870

Brand: Abit Pages: 120

Brand: AOpen Pages: 8

Kontron mITX-CFL-S

Brand: S&T Pages: 8

Brand: NXP Semiconductors Pages: 269

TA870 PLUS - SETUP 2

Brand: Biostar Pages: 67

Brand: Xilinx Pages: 31

Brand: Gigabyte Pages: 31

Brand: DFI Pages: 115

Brand: ITX SECURITY Pages: 18

Brand: Mercury Pages: 57

Brand: IDT Pages: 39

WAFER-BW-N4-R10

Brand: IEI Technology Pages: 136

TLV320AIC12KEVM-K

Brand: Texas Instruments Pages: 40

Brand: NXP Semiconductors Pages: 138

Brand: ON Semiconductor Pages: 5

LanParty UT NF4 SLI EXPERT Venus

Brand: DFI Pages: 161

Brand: IEI Technology Pages: 147

K10N780SLIX3-WIFI

Brand: ASROCK Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands