manualshive.com logo in svg

Samsung S5PC110, Manual

Introducing the Samsung S5PC110 - an innovative device offering cutting-edge features and impressive performance. Discover the full potential of this exceptional product with our user manual, available for free download at manualshive.com. Explore the detailed instructions and get the most out of your Samsung S5PC110 experience.

Share
Download
background image

S5PC110_UM   

5 INTELLIGENT ENERGY MANAGEMENT 

  

5-37 

5.5.3.11  APC Interrupt Status Register (APC_ISTATUS, R, Address = 0xE070_002C) 

APC_ISTATUS 

Bit 

Description 

Initial State

Reserved [7] 

Read 

undefined. 

0 

APB Write Discard 

[6] 

When the PWI command is active in the APC1, the new 
PWI commands issued by the host are discarded. This 
discarded status is reflected in this bit. 

0 

PWI Transaction Done 

[5] 

Bit is set when the APC1 completes the host issued PWI 
command. Software has to check this bit as well as the 
APC_STATUS.PWI_BUSY bit to confirm the completion 
of the command. 

0 

Error Detected in PWI 

[4] 

Bit is set on an error response from the PWI slave for the 
host issued as well as the APC1 issued PWI commands. 

0 

No PWI Slave Response 

[3] 

Bit is set for no response from the PWI slave for the host 
issued as well as the APC1 issued commands. 

0 

Output Voltage Clamped 

[2] 

This bit is set when the output voltage is clamped to the 
minimum limit or to the zero voltage. 

0 

Low VDD Timeout 

[1] 

During upward voltage slew, this bit is set in the closed-
loop mode indicating that the dynamic compensator is 
not able to increase the voltage to the required level for 
the new higher performance level within the maximum 
time period set by the hardware. 

0 

Undershoot Interrupt 

[0] 

  In the closed-loop AVS operation for a performance 
level change after reaching the optimum voltage the 
APC1 asserts an interrupt if the voltage correction 
continues and results in a slack error (+ve) which is more 
than the undershoot_limit value programmed in the 
APC_UNSHT_NOISE Register for nine consecutive 
samples. 

0 

 

5.5.3.12  APC Interrupt Clear Register (APC_ICLEAR, W, Address = 0xE070_0030) 

APC_ICLEAR 

Bit 

Description 

Initial State 

Reserved 

[7] 

Undefined. Write as zero. 

0 

APB Write Discard 

[6] 

The APB write is discarded. 

0 

PWI Transaction Done 

[5] 

The PWI transaction is completed. 

0 

Error Detected in PWI 

[4] 

Error is detected in PWI response frame. 

0 

No PWI Slave Response 

[3] 

No response frame is detected on PWI interface. 

0 

Output Voltage Clamped 

[2] 

The output voltage is clamped to minimum limit or zero 
voltage. 

0 

Low VDD Timeout 

[1] 

In the closed-loop mode, Vdd has not reached the target 
voltage in the programmed time period for the upward 
voltage slew. 

0 

Undershoot Interrupt 

[0] 

Undershoot interrupt. 

0 

Summary of Contents for S5PC110



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S5PC110

Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
XMG OASIS Disassembly Procedure preview
OASIS
Brand: XMG Pages: 5
NAD M10 Quick Setup Manual preview
M10
Brand: NAD Pages: 2
Campbell NL115 Instruction Manual preview
NL115
Brand: Campbell Pages: 42
Harman Kardon CITATION 7.0 Owner'S Manual preview
CITATION 7.0
Brand: Harman Kardon Pages: 66
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Brand: RAIDAGE Pages: 60
Aaeon SBC-555 Manual preview
SBC-555
Brand: Aaeon Pages: 72
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
Quatech SSPX-100 User Manual preview
SSPX-100
Brand: Quatech Pages: 5
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Brand: Grundfos Pages: 40
Kontron KISS Stor Slim Quick Installation Manual preview
KISS Stor Slim
Brand: Kontron Pages: 4
NCR VOYIX 7772-K141 Kit Instructions preview
VOYIX 7772-K141
Brand: NCR Pages: 10
Ericsson Baseband 6648 Manual preview
Baseband 6648
Brand: Ericsson Pages: 16
Extron electronics EDID 101D User Manual preview
EDID 101D
Brand: Extron electronics Pages: 20
Crestron C2N-IO Installation Manual preview
C2N-IO
Brand: Crestron Pages: 2
TDK Supereta Series DC/DC Specification Sheet preview
Supereta Series DC/DC
Brand: TDK Pages: 2
Fairchild SEMICONDUCTOR RC5050 Application Note preview
SEMICONDUCTOR RC5050
Brand: Fairchild Pages: 24
Huawei E8278 Quick Start Manual preview
E8278
Brand: Huawei Pages: 96

Brands by name

Popular brands

Load more brands