Samsung S5PC110 Manual Download Page 1378 | Manualshive

Page: 1378 / 2426

background image

S5PC110_UM

4 3BMIPI CSIS

4-11

4.6.1.6 Interrupt Source Register (CSIS_INTSRC, R/W, Address = 0xFA60_0014)

This register identifies interrupt sources.

CSIS_INTSRC

Bit

Description

Initial State

EvenBefore [31]

Receives

non-image data at even frame and before

image.
Write 1 = Clears the status bit
Write 0 = No effect

0

EvenAfter [30]

Receives

non-image

data at even frame and after image.

Write 1 = Clears the status bit
Write 0 = No effect

0

OddBefore [29]

Receives

non-image

data at odd frame and before image.

Write 1 = Clears the status bit
Write 0 = No effect

0

OddAfter

[28]

Receives non-image data at odd frame and after image.
Write 1 = Clears status bit
Write 0 = No effect

0

Reserved [27:16]

Reserved

0

ERR_SOT_HS [15:12]

Specifies

start of transmission error.

0

Reserved [11:6]

Reserved

0

ERR_LOST_FS

[5]

Indicates the lost of Frame Start packet

0

ERR_LOST_FE

[4]

Indicates the lost of Frame End packet

0

ERR_OVER

[3]

Specifies overflow caused in image FIFO. The outer
bandwidth has to be faster than the input bandwidth.
However, image FIFO can overflow due to user fault.
There are two ways to prevent overflow:
Tune output pixel clock faster than current: WCLK_Src in
CSIS_CTRL register should be set to 1. Then assign a
faster clock.
Tune input byte clock slower than current: Set register in
camera module through I2C channel.
When this interrupt is generated,
Turn the camera off.
Assert software reset. If you do not assert software reset,
MIPI CSIS will not receive any data.
Tune the clock frequency and re-configure all the related
registers. MIPI CSIS module is now ready for operation.
Write 1 = Clears the status bit.
Write 0 = Has no effect.

0

ERR_ECC

[2]

Specifies ECC error.
Write 1 = Clears status bit
Write 0 = No effect

0

ERR_CRC

[1]

Specifies CRC error.
Write 1 = Clears status bit
Write 0 = No effect

0

«
...
1376
1377
1378
1379
1380
...
»

Summary of Contents for S5PC110



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S5PC110

Brand: Harman Kardon Pages: 66

CompactPCI CC8-BLUES

Brand: EKF Electronik Pages: 52

Brand: peplink Pages: 2

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

IMACS Network Device

Brand: Zhone Pages: 114

Brand: IDT Pages: 207

UM10301 PCA8565

Brand: NXP Semiconductors Pages: 54

Brand: Abit Pages: 22

Suzie-Q 541.35.520

Brand: Hafele Pages: 12

Aquaduct 240 eco

Brand: Aqua Computer Pages: 20

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

Brand: PairGain Pages: 80

Brand: Keysight Technologies Pages: 106

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Brand: Paradyne Pages: 216

Brand: NEC Pages: 170

IntelliStripe 65

Brand: Magtek Pages: 44

Brand: Advantage Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands