Samsung S5PC110 Manual Download Page 1018 | Manualshive

Page: 1018 / 2426

background image

S5PC110_UM

7 SD/MMC CONTROLLER

7-38

7.9.6 TRANSFER MODE REGISTER

7.9.6.1 Transfer Mode Register Setting

•

TRNMOD0, R/W, Address = 0xEB00_000C

•

TRNMOD1, R/W, Address = 0xEB10_000C

•

TRNMOD2, R/W, Address = 0xEB20_000C

•

TRNMOD3, R/W, Address = 0xEB30_000C

This register is used to control the data transfer operations. The Host Driver sets this register before issuing a
command which transfers data (Refer to Data Present Select in the Command register (9.7)), or before issuing a
Resume command. The Host Driver saves the value of this register if data transfer is suspended (as a result of a
Suspend command) and restore it before issuing a Resume command. To prevent data loss, the Host Controller
implements write protection for this register during data transactions. Writes to this register is ignored if the
Command Inhibit (DAT) in Present State register is 1.

TRNMOD

Bit

Description

Initial State

Reserved [15:14]

Reserved

0

BOOTACK

[13]

Boot ACK Receive Enable when Boot mode

0

BOOTCMD

[12]

Boot Command mode Enable
Note: In boot mode, Do Not Enable “Auto CMD12 Enable”

0

Reserved

[11:10] Reserved

0

CCSCON

[9:8]

Command Completion Signal Control
'00' = No CCS Operation (Normal operation and No CE-ATA
mode)
'01' = Read or Write data transfer CCS enable (Only CE-ATA
mode)
'10' = Without data transfer CCS enable (Only CE-ATA mode)
'11' = Abort Completion Signal (ACS) generation (Only CE-ATA
mode)

0

Reserved [7:6]

Reserved

0

MUL1SIN0

[5]

Multi/ Single Block Select
This bit enables multiple block DAT line data transfers. For any
other commands, this bit is set to 0. If this bit is 0, it is not
mandatory to set the Block Count register. (Refer to the Table
below "Determination of Transfer Type")
1 = Multiple Block
0 = Single Block

0

RD1WT0

[4]

Data Transfer Direction Select
This bit defines the direction of DAT line data transfers.
The bit is set to 1 by the Host Driver to transfer data from the SD
card to the SD Host Controller and it is set to 0 for all other
commands.
1 = Read (Card to Host)
0 = Write (Host to Card)

0

Reserved

[3]

Reserved

0

«
...
1016
1017
1018
1019
1020
...
»

Summary of Contents for S5PC110



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S5PC110

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: Longshine Pages: 35

Brand: mikroElektronika Pages: 2

Brand: IEI Technology Pages: 136

Brand: H3C Pages: 68

Brand: ExtraHop Pages: 2

Brand: Xinje Pages: 76

Brand: Juniper Pages: 6

Brand: R.V.R. Elettronica Pages: 171

RJModem MT5656RJ

Brand: Multi-Tech Pages: 27

Brand: ICP Pages: 111

Brand: Xtreme Pages: 83

Brand: R3 Pages: 48

Brand: Cisco Pages: 12

Brand: Cisco Pages: 74

Brand: Cisco Pages: 26

Brand: Cisco Pages: 8

SA-VAM - VPN Acceleration Module

Brand: Cisco Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands