Siemens SINAMICS G130 Скачать руководство пользователя страница 1592 | Manualshive

Страница: 1592 / 1976

background image

4 Faults and alarms
4.2 List of faults and alarms

SINAMICS G130/G150

1592

List Manual (LH2), 07/2016, A5E03263479A

For rotary encoders, the maximum possible absolute position (LU) is calculated as follows:
1. Motor encoder without position tracking:
p2506 * p0433 * p2505 / (p0432 * p2504)
p2506 * p0433 * p2505 * p0421 / (p0432 * p2504) for multiturn encoders
2. Motor encoder with position tracking for measuring gear
p2506 * p0412 * p2505 / p2504
3. Motor encoder with position tracking for load gear:
p2506 * p2721 * p0433 / p0432
4. Motor encoder with position tracking for load and measuring gear:
p2506 * p2721
5. Direct encoder without position tracking:
p2506 * p0433 / p0432
p2506 * p0433 * p0421 / p0432 for multiturn encoders
6. Direct encoder with position tracking for measuring gear:
p2506 * p0412
For a linear encoder, the following must be maintained:
- p0407 * p2503 / (2^p0419 * 10^7) <= 1.0

Reaction upon A:

NONE

Acknowl. upon A:

NONE

F07600 (A)

Encoder 2: Adjustment not possible

Message value:

Drive data set: %1

Message class:

Error in the parameterization / configuration / commissioning procedure (18)

Drive object:

VECTOR_G

Component:

Encoder 2

Propagation:

GLOBAL

Reaction:

OFF1 (NONE, OFF2, OFF3)

Acknowledge:

IMMEDIATELY

Cause:

The maximum encoder value times the factor to convert the absolute position (r0483 and/or r2723) from increments
to length units (LU) has exceeded the value range (-2147483648 ... 2147483647) for displaying the position actual
value.

Remedy:

If the value for the maximum possible absolute position (LU) is greater than 4294967296, then it is not possible to
make an adjustment due to an overflow.
For rotary encoders, the maximum possible absolute position (LU) is calculated as follows:
1. Motor encoder without position tracking:
p2506 * p0433 * p2505 / (p0432 * p2504)
p2506 * p0433 * p2505 * p0421 / (p0432 * p2504) for multiturn encoders
2. Motor encoder with position tracking for measuring gear
p2506 * p0412 * p2505 / p2504
3. Motor encoder with position tracking for load gear:
p2506 * p2721 * p0433 / p0432
4. Motor encoder with position tracking for load and measuring gear:
p2506 * p2721
5. Direct encoder without position tracking:
p2506 * p0433 / p0432
p2506 * p0433 * p0421 / p0432 for multiturn encoders
6. Direct encoder with position tracking for measuring gear:
p2506 * p0412
For a linear encoder, the following must be maintained:
- p0407 * p2503 / (2^p0419 * 10^7) <= 1.0

Reaction upon A:

NONE

Acknowl. upon A:

NONE

«
...
1590
1591
1592
1593
1594
...
»

Содержание SINAMICS G130

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SINAMICS G130

SC825MTQ-R700LPB

Бренд: Supermicro Страницы: 78

Бренд: Xena Networks Страницы: 6

Бренд: Solid State Logic Страницы: 52

Бренд: Tiger Technology Страницы: 26

apollo 4510 gen9

Бренд: HP Страницы: 68

BladeSystem c7000

Бренд: HP Страницы: 80

Бренд: HP Страницы: 49

EMC PowerEdge MX7000

Бренд: Dell Страницы: 48

Бренд: Viavi Страницы: 132

Бренд: CTC Union Страницы: 20

Бренд: Addonics Technologies Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды