Home
/
Siemens
/
SINAMICS S Series
/
List Manual

Siemens SINAMICS S Series, List Manual

Share

Page: 395 / 1816

Siemens SINAMICS S Series List Manual Download Page 395

List of parameters

Parameters

1-395

© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007

Dependency:

In conjunction with p1428, this parameter can simulate the characteristics of how torque is established (dynamic
response of the closed current control loop).

For VECTOR (r0107) the following applies:

The parameter is only effective if the acceleration model is supplied using external acceleration signals (p1400.2 =
1). For p1400.2 = 0, time constant p1442 (or p1452 for sensorless vector control) is used.

Refer to: p1428, p1511

Description:

Sets the time constant (PT1) for symmetrizing the velocity setpoint for active force pre-control.

Dependency:

In conjunction with p1428, this parameter can simulate the characteristics of how the force is established (dynamic
response of closed current control loop).

Refer to: p1428, p1511

Description:

Sets the signal source for speed pre-control channel (speed pre-control or torque pre-control).

Notice:

The parameter may be protected as a result of p0922 or p2079 and cannot be changed.

Description:

Sets the signal source for the velocity pre-control channel (velocity pre-control or force pre-control).

Notice:

The parameter may be protected as a result of p0922 or p2079 and cannot be changed.

Description:

Displays the speed pre-control value after symmetrizing for the torque build-up (emulates the closed current control
loop).

Dependency:

Symmetrizing can be parameterized with p1428 and/or p1429.

p1429[0...n]

Velocity pre-control balancing time constant / n_prectr bal T

SERVO (Lin)

Can be changed:

U, T

Calculated:

-

Access level:

3

Data type:

Floating Point

Dynamic index:

DDS, p0180

Func. diagram:

5030, 5042,

5210

P-Group:

Closed-loop control

Units group:

-

Unit selection:

-

Not for motor type:

REL

Expert list:

1

Min Max

Factory

setting

0.00 [ms]

10000.00 [ms]

0.00 [ms]

p1430[0...n]

CI: Speed pre-control / n_prectrl

SERVO

Can be changed:

T

Calculated:

-

Access level:

3

Data type:

Unsigned32 / FloatingPoint32

Dynamic index:

CDS, p0170

Func. diagram:

1550, 1590,

5020

P-Group:

Closed-loop control

Units group:

-

Unit selection:

-

Not for motor type:

REL

Expert list:

1

Min Max

Factory

setting

- -

0

p1430[0...n]

CI: Velocity pre-control / v_prectrl

SERVO (Lin)

Can be changed:

T

Calculated:

-

Access level:

3

Data type:

Unsigned32 / FloatingPoint32

Dynamic index:

CDS, p0170

Func. diagram:

1550, 1590,

5020

P-Group:

Closed-loop control

Units group:

-

Unit selection:

-

Not for motor type:

REL

Expert list:

1

Min Max

Factory

setting

- -

0

r1432

CO: Speed pre-control after symmetrizing / n_prectr after sym

SERVO

Can be changed:

-

Calculated:

-

Access level:

3

Data type:

Floating Point

Dynamic index:

-

Func. diagram:

5030

P-Group:

Closed-loop control

Units group:

3_1

Unit selection:

p0505

Not for motor type:

REL

Expert list:

1

Min Max

Factory

setting

- [RPM]

- [RPM]

- [RPM]

«
...
393
394
395
396
397
...
»

Summary of Contents for SINAMICS S Series

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands