Intel ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3 Manual Download

Page: 623 / 1898

Volume 2, Part 1: Processor Abstraction Layer

2:375

PAL_CACHE_INFO

cache if the cache contents never get flushed to memory (for example an
instruction cache).

•

stride

–

Unsigned 8-bit integer denoting the binary log of the most effective stride

in bytes for flushing the cache.

•

store_latency

–

Unsigned 8-bit integer denoting the number of cycles after issue

until the value is written into the cache. If the cache cannot accept a store (like an
instruction cache) the value returned will be 256 (0xff).

•

load_latency

–

Unsigned 8-bit integer denoting the number of processor cycles after

issue until the value may be used if it is found in the cache.

•

store_hints

–

8-bit vector denoting hints implemented by the processor store

instruction. For instruction caches this bit vector will be zero indicating no store
hints are supported.

•

load_hints

–

8-bit vector denoting hints implemented by the processor load

instruction.

The

config_info_2

return value has the following structure:

•

cache_size

–

Unsigned 32-bit integer denoting the size of the cache in bytes.

•

alias_boundary

–

Unsigned 8-bit integer indicating the binary log of the minimum

number of bytes which must separate aliased addresses in order to obtain the
highest performance.

•

tag_ls_bit

–

Unsigned 8-bit integer denoting the least-significant address bit of the

tag.

•

tag_ms_bit

–

Unsigned 8-bit integer denoting the most-significant address bit of the

tag.

Table 11-68. Cache Store Hints

Bits

Description

Temporal, level 1

2:1

Reserved

Non-temporal, all levels

7:4

Reserved

Table 11-69. Cache Load Hints

Bits

Hint

Temporal, level 1

Non-temporal, level 1

Reserved

Non-temporal, all levels

7:4

Reserved

Figure 11-3.

config_info_2

Return Value

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9

cache_size

63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32

reserved

tag_ms_bit

tag_ls_bit

alias_boundary

Summary of Contents for ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Reviews:

Related manuals for ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Brands by name

Popular brands

Intel ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3, Manual

Search results

Summary of Contents for ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Reviews:

Related manuals for ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Brands by name

Popular brands