manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 325

Test Setup - Test Configurator, Timer, and System

Power Blazer

313

Streams - Global

Streams - Global 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, the protocol block, and 

the 

Global 

tab. 

The following parameters are displayed and configurable per stream. 

Check boxes:

The first check box (top-left) allows enabling stream(s) sequentially 
within the limit of the link capacity. 

The check boxes next to the stream numbers allow enabling each 
stream individually within the limit of the link capacity. 

Stream Name

1

 indicates the name of each stream. Tap on the 

Stream 

Name

 button to modify the name of each stream. 

Frame Size

1

 indicates the frame size of each stream. Tap on the 

Frame 

Size

 button to modify the frame size of each stream. 

TX Rate

1

 indicates the transmission rate for each stream. Tap on the 

TX Rate

 button to modify the transmission rate (see page 319). 

Framing

 indicates the framing of each service. Tap on the 

Framing

 

button to modify the 

Frame Format

, 

Network Layer

, 

Transport Layer

, 

VLAN

, and 

MPLS

 when applicable (see 

Modify Frame Structure

 from 

the 

MAC/IP/UDP

 on page 204). 

VLAN

 indicates the ID and Priority of each VLAN level for each stream. 

Tap on the 

VLAN

 button to modify the VLAN settings (see 

VLAN

 from 

the 

MAC/IP/UDP

 tab). 

1. See the Profile tab for more information.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands