manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 92

Test Setup - Test Applications

80

88000 Series

CPRI/OBSAI BERT

Typical CPRI/OBSAI BERT test applications: 

Note:

A RRH is typically not capable to perform a loopback of the traffic so BERT 
test monitoring is not applicable. The BERT test is more common when 
testing between two test units. 

Additional CRPI BERT test application: 

Supported Interfaces/Rates: 
CPRI: 1.2, 2.4, 3.1, 4.9, 6.1, and 9.8 Gbit/s
OBSAI: 1.5, 3.1, and 6.1 Gbit/s.

Network

under test

Testing Unit

Testing Unit

EXFO Module

Unframed, 

Framed L2

EXFO Module

Network

under test

Testing Unit

Physical Loopback 

EXFO Module

Unframed 

Network

under test

Base Station (BTS)

EXFO Module

Framed L2

RRH or 

EXFO Module

Network

under test

Testing Unit

EXFO Module

Testing Units

EXFO Module

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands