manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 337

Test Setup - Test Configurator, Timer, and System

Power Blazer

325

System

System 

From the 

Test

 menu, tap 

Setup

, and 

System

.

Factory Default

Restore Default

 button restores the factory default settings for all test 

applications. 

Restore Default at Start-Up

 check box when cleared (default), 

reloads the last configuration settings when the application is 
launched; when selected, the factory settings are restored. 

Remote Control 

User Information

 allows a user to leave a message to other users 

connected on the same module. Up to 80 characters are allowed. 

Time Zone

 allows the selection of the time zone source. 

Local

 (default) uses and displays the time from the 88000 Series 

module or from the PC for a Remote ToolBox session. 

Test Equipment

, available for a Remote ToolBox session, uses and 

displays the time from the 88000 Series module. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands