manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 559

Test Functions

Power Blazer

547

40/100G/400G Advanced - Lanes Mapping & Skew

Default/Random/Manual Mapping

Allows changing the PCS/Logical lane mapping that will be used for the 
test. Not available with 100 GbE client in OTU4. 

Default Mapping

 sets the TX mapping to the default numerical order 

value which corresponds to the ascending PCS/Logical lane order. 

Random Mapping

 sets the TX mapping in a random order. Each time 

the button is tapped, random alignment markers are assigned to each 
PCS/Logical lane. 

Manual Mapping

 allows setting the TX mapping manually. 

PCS/Logical Lane/Lane Marker 

and 

Assigned Status

: 

The 

PCS/Logical Lane/Lane Marker

 buttons allow assigning the 

corresponding Lane Marker to the selected PCS/Logical or 
400GAUI-16/CAUI/XLAUI/Physical Lane mapping (the one pointed 
by the arrow). The 

Assigned Status

 column displays a check mark 

next to the assigned PCS/Logical Lanes. Range is from 

0

 to 

15

 for 

400G, 

0

 to 

19

 for OTU4/100G, and 

0

 to 

3

 for 

OTU3/OTU3e1/OTU3e2/40G. 

PCS/Logical Lane

 and 

400GAUI-16/CAUI/XLAUI/Physical Lane

 

columns indicate the target PCS/Logical to 
400GAUI-16/CAUI/XLAUI/Physical mapping. 

Clear All

 clears the PCS/Logical to 400GAUI-16/CAUI 

/XLAUI/Physical Lane assignments.

OK

 accepts the new PCS/Logical to 

400GAUI-16/CAUI/XLAUI/Physical lane mapping. All target 
PCS/Logical Lane fields must contain an assignation, including 
duplicates, to give access to the 

OK

 button.

Note:

A PCS/Logical Lane marker can be assigned more than once. If this is the 
case, a red background is used to highlight all occurrences of this 
PCS/Logical Lane marker. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands